mundoclima AEROTHERM MAM-V9 Serie Manual De Usuario E Instalacion página 162

Symptom 3: Pump is making noise (cavitation)
POSSIBLE CAUSES
There is air in the system.
Water pressure at pump
inlet is too low.
Symptom 4: The water pressure relief valve opens
POSSIBLE CAUSES
The expansion vessel isbroken.
The filling water pressure
in the installation is
higher than 0.3MPa.
Symptom 5: The water pressure relief valve leaks
POSSIBLE CAUSES
Dirt is blocking the water
pressure relief valve
outlet.
Symptom 6: Space heating capacity shortage at low outdoor temperatures
POSSIBLE CAUSES
Backup heater operation
is not activated.
Too much heat pump
capacity is used for
heating domestic hot
water (applies only to
installations with a
domestic hot water tank).
Symptom 7: Heat mode can't change to DHW mode immediately
POSSIBLE CAUSES
Volume of tank is too
small and the location of
water temperature probe
not high enough
CORRECTIVE ACTION
Purge air.
‡ &KHFN RQ WKH PDQRPHWHU WKDW WKHUH LV VXIILFLHQW ZDWHU SUHVVXUH
The water pressure must be > 1 bar (water is cold).
‡ &KHFN WKDW WKH PDQRPHWHU LV QRW EURNHQ
‡ &KHFN WKDW WKH H[SDQVLRQ YHVVHO LV QRW EURNHQ
‡ &KHFN WKDW WKH VHWWLQJ RI WKH SUH SUHVVXUH RI WKH H[SDQVLRQ
vessel is correct (refer to "9.3 water piping/Checking the
water volume and expansion vessel pre-pressure").
CORRECTIVE ACTION
Replace the expansion vessel.
Make sure that the filling water pressure in the installation is about
0.15~0.20MPa (refer to "9.3 water piping/Checking the water volume and
expansion vessel pre-pressure").
CORRECTIVE ACTION
Check for correct operation of the pressure relief valve by turning the red
knob on the valve counter clockwise:
‡ ,I \RX GR QRW KHDU D FODFNLQJ VRXQG FRQWDFW \RXU ORFDO GHDOHU
‡ ,Q FDVH WKH ZDWHU NHHSV UXQQLQJ RXW RI WKH XQLW FORVH ERWK WKH
water inlet and outlet shut-off valves first and then contact your
local dealer.
CORRECTIVE ACTION
Check that the "OTHER HEATING SOURCE/ BACKUP HEATER"is
enabled, see "10.7 Field settings" Check whether or not the thermal
protector of the backup heater has been activated (refer to "Controls parts
for backup heater(IBH) " ). Check if booster heater is running, the backup
heater and booster heater can't operate simultaneously.
Check that the "t_DHWHP_MAX" and "t_DHWHP_RESTRICT" are
configured appropriately:
‡ 0DNH VXUH WKDW WKH ³'+: 35,25,7<´ LQ WKH XVHU LQWHUIDFH LV
disabled.
‡ (QDEOH WKH ³7B7%+B21´ LQ WKH XVHU LQWHUIDFH)25 6(59,&(0$1
to activate the booster heater for domestic water heating.
CORRECTIVE ACTION
‡ 6HW ³G76´ WR °C, and set "t_DHWHP_RESTRICT" to minimum value.
‡ 6HW G76+ WR °C.
‡ (QDEOH 7%+ DQG 7%+ VKRXOG EH FRQWUROHG E\ WKH RXWGRRU XQLW
‡ ,I $+6 ERLOHU LV DYDLODEOH WXUQ ERLOHU RQ ILUVW LI UHTXLUHPHQW IRU
turn heat pump on is fullfilled, the heat pump will turn on.
‡ ,I ERWK 7%+ DQG $+6 DUH QRW DYDLODEOH WU\ WR FKDQJH WKH SRVWLRQ
of T5 probe(refer to 2 General information/Domestic hot water
tank).
159