Technical Data; Flexible Shaft - SUHNER ROTOFERA STM Instrucciones De Uso

Read the enclosed safety instructions,
Erection instructions
1. Rotofera: Technical data

2. Flexible shaft

3. Start-up procedures:
3.1 Set the operating speed
3.2 Connect the flexible shaft
3.3 Connect the SAK safety clutch
3.4 Connect toolholders
3.5 Start-up with SAK
4. Accessories: FH10, WI10, BSG10, FSM
1. Rotofera
F=base plate STM=trolley mounted
Machine elements: See Fig. A
A1 On/Off switch A3 Speed indicator
A2 Retention pin A4 Speeds

Technical data

Power input / output three - phase
Power input / output single - phase
Insulation protection class
Voltage (see spare parts list)
Ground fault protection : Used for tools
with water feed or in humid environments.
No load speeds
7-speed gear box
Sound pressure level CEN/TC 255 N
Flexible shaft connection
For flexible shaft types:
(see catalogue)
Vibration values ISO/DIS 8662-4
Toolholder type: Test plate:
FH10 ø 80 x 10
WI10 ø 50 x 6
BSG 10 ø 100 x 25
FSM 1:1 ø 180 x 6
Maintenance
• Store machine in a dry, clean place.
• Cooling air ports must be kept free of obstructions.
• Unplug before performing any maintenance work.
• Change gear grease every 12 months. Your SUHNER Service Centre
can perform this work quickly and efficiently.
• Check connecting cables regularly. Damaged cables must be replaced
under all circumstances.
• Repairs may only be performed by a qualified electrician Accidents
could otherwise occur for the operator.
• Complaints can only be accepted if the machine is returned unopened.
2. Flexible shaft
See Fig. B
Machine elements:
B1 M10 threaded coupling
B2 DIN 10 casing coupler
B3 Spring-loaded pin
Type: NA10 DIN 10 / G28, permissible operating speed
Type: NA12 DIN 10 / G28, permissible operating speed
Maintenance
• Store flexible shaft in a dry, clean place.
• If used daily: Re-grease once monthly. Remove core B5 from casing
B4. Remove shaft grease. Lightly apply SUHNER shaft grease to core
B5. Order No. for 1 kg can : 904 832.
appendix 39 230 ..!
appendix 39 328 ..!
GB
HM=hanging attachment
A5 Excenter
A6 Motor shaft
1'000 / 750
800 / 550
IP44
Various
45 V
50 Hz 60 Hz
12' 000 14' 400
8' 000 9' 600
5' 700 6' 800
3' 200 3' 800
2' 100 2' 500
1' 600 1' 900
850 1' 000
79 81 dB (A)
DIN 10 =M10 see A6
NA 10 DIN 10 / G28 see B2 B8
NA 12 DIN 10 / G28
Measured value: Excenter stage:
2
< 2,5 m/s 12' 000 RPM
< 2,5 m/s 2 12 '000 RPM
2
< 2,5 m/s 5' 700 RPM
2
< 2,5 m/s 8' 000 RPM
B4 Casing
B5 Core
B6 Driving pin
B7 Spring-loaded pin
B8 G28 casing coupler
15' 000
12' 000
• New shafts or newly greased shafts require running-in.
• Clean casing coupler B2 B8 before use. Worn casing couplers lead to
increased vibration and noise. The casing B4 must then be replaced
(see spare parts list).
3. Set the operating speed
1
See Fig. A
• Only change speed when machine is switched off. A1 Wait until gears
are completely motionless. Unplug power supply.
• Ensure that the desired speed A4 is permissible for the tool and
toolholder used.
1. Remove retention pin A2.
2. Turn excenter A5 clockwise until it reaches the limit stop. Release
retention pin A2. All speeds must be visible in this position.
3. Move excenter A5 axially until the correct
4. operating speed A4 is positioned in the speed indicator A3.
5. Turn excenter A5 all the way to the left.
6. Retention pin A2 must click audibly into place.
7. Ensure that the correct operating speed is positioned directly and
centrally in the speed indicator A3. If the retention pin does not click
into place, or the selected speed is not displayed in the center, the
procedure must be repeated from Step 1 .
• Attention : In case the machine is operated in one gear position only -
one must at least once a week switch through all positions for a brief
period in order to redistribute the grease for long gear service life.
(run without flex.Shaft and handpiece)
W
W
3. Connect the flexible shaft
2
See Figs. A + B
1. Insert pin in retention hole.
2. Slightly withdraw threaded coupling B1 from casing coupler B2.
3. Insert second pin through transverse hole in threaded coupling B1 and
4. Fasten tightly onto the motor shaft A6.
5. Remove pins.
RPM
6. Insert casing coupler B2 completely into excenter hole A5.
7. Depress spring-loaded pin B3 and completely insert casing coupler
B2.
8. Spring-loaded pin B3 must click audibly into place in the retention
hole. Ensure that spring-loaded pin B3 has locked firmly into place. If
necessary, move/rotate casing coupler B2 until spring-loaded pin B3
clicks into place.
3. Connect the SAK safety clutch
3
See Fig. C
Machine elements:
C1 Retention hole
C2 Safety lever
Use the Type SAK G28 safety clutch to protect operator from accidental
start-up.
1. Insert casing coupler B8 into tool connection.
2. Depress spring-loaded pin B7 and completely insert casing
coupler B8.
3. Spring-loaded pin B7 must click audibly into place in retention hole
C1. Ensure that spring-loaded pin B7 has locked firmly into place. If
necessary, move/rotate casing coupler B8 until spring-loaded pin B7
clicks into place.
3. Connect toolholders
4
See Fig. C
The connection of toolholders corresponds to the procedure described
in Item 3.3.
Note: Toolholders WI10, BSG10 and FSM can be rotated on the casing
coupler for easier handling.
3. Start-up with SAK safety clutch ( deadman switch)
5
See Fig. D
Only with machine in OFF position !
1. Depress locking pin C3.
2. Completely depress safety lever C2. If necessary, move to starting
position by turning the working spindle D1 and repeatedly depressing
safety lever C2.
RPM
• Attention : The powerfull machine develops a heavy torque when
RPM
switched-on. Thus secure yourself in a rigid position and hold on to
the handpiece.
• Switch on drive motor A1.
• Switch off by releasing lever C2. Torque transmission to the toolholder
is interrupted. Locking pin C3 protects from automatic start-up.
• Switch machine off in order to return safety lever C2 to starting
position!
(Excenter switch)
to the motor
(accessory)
C3 Locking pin C5 Driving pin
C4 Spring-loaded pin