Operations; Basic Operations - Clarion DXZ948RMP Manual De Instrucciones

6. OPERATIONS

Basic Operations

CAUTION
Be sure to lower the volume before
switching the unit off or the ignition key. The
unit remembers its last volume setting. If
you switch the power OFF with the volume
up, when you switch the power back ON, the
sudden loud volume may hurt your hearing
and damage the unit.
Turning ON/OFF the power
Turning on
Note:
• Be careful when using this unit for a long time
without running the engine. If you drain the car's
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [ROTARY] knob.
The mode that was previously active is
displayed.
System check
The first time that this unit is turned on after wire
connections are completed, this unit checks
which equipment is connected. (This is called
the "system check.") When the power is turned
ON, and "System Check" is displayed, follow
the procedure below to perform the system
check.
1. When "System Check" appears on the
display, press the [ROTARY] knob.
The system check starts.
When the system check is complete,
"Completed" appears on the display.
2. Press the [ROTARY] knob again.
The main display for the radio mode
appears.
12
DXZ948RMP
CODEMATIC function
When "CODEMATIC" is set to "ON", and the
power is turned ON with the DCP attached, the
Touch Code display appears. Touch the display
in the order that was set in the adjust mode.
For details on the CODEMATIC function, see
"Using the security function (CODEMATIC)"
(cf. page 50).
Turning off
1. Hold down the [ROTARY] knob for 1 second
or longer.
Selecting a mode
1. Press the [ROTARY] knob to change the
operation mode.
2. Each time you press the [ROTARY] knob,
the operation mode changes in the following
order:
Radio mode DAB mode CD/MP3
mode CD changer mode DVD
changer mode TV mode AUX mode
Radio mode...
∗ External equipment not connected with
CeNET is not displayed.
Adjusting the volume
1. Turning the [ROTARY] knob clockwise
increases the volume; turning it
counterclockwise decreases the volume.
∗ The volume level is from 0 (minimum) to
33 (maximum).
Switching the operation mode
There are 2 basic operation modes: standard
operation and simple operation.
1. In the main display screen, touch and hold
the left of the display for 1 second or longer.
The operation mode is switched.
SIMPLE MODE
MODE
B
98.10MHz
BAND
In the simple operation, the operations of
touching or in the radio mode or
CD mode main display screen are not required,
and this unit can be used by performing simple
operation.
Note, however, that the following operations are
not available in the simple operation.
• Preset tuning, folder selection, disc selection,
and other operations that involve touching
on the right of the display
• Display switching operations (cf. page 13)
• Title display switching operations (cf. page 14)
• Operations for displaying title entry screens.
In screens (e.g. list display, adjust mode, etc.)
other than the main display, there is no
difference between the standard operation
and the simple operation.
Descriptions given in this manual are mainly for
the standard operation. For descriptions for
operations in the simple operation, refer to the
descriptions for the screen displays in the radio
mode or the CD mode.
Basic Operations
Switching the display
1. Touch the centre of the display.
Each time you touch the display, it changes
as follows:
Title display
PS NAME
MODE
FM1
4 2
3 B
98.10MHz
BAND
Spectrum Analyzer display
S/A SCAN
MODE
FM1
4 2
3 B
98.10MHz
BAND
Time display
MODE
1 0 : 0 5 1 0 : 0 5 C T C T
FM1
4 2
3 B
98.10MHz
BAND
Screen saver
When the screen saver function is set to "ON",
and you do not operate this unit for about 30
seconds, the screen saver will be displayed. For
details, see page 41.
DXZ948RMP
13