Safety Parameters - BM2 BIEMMEDUE DUSTY 1100 ET Manual De Uso Y Mantenimiento

Technical data
Power Honda GX160 engine (hp)
Starting motor power
Starting battery
Tank capacity (l)
Drive
Total installed power (W)
Total installed power (W) PLUS
Main voltage
Battery duration (h) *
Type of batteries
Battery charger
Centr. brush motor
Suction motor
Vibrator motor
Traction motor
Emptying motor
Maximum working slope
*: The duration of the batteries is calculated with new, recently
charged, perfectly operational batteries, operating on a smooth flat
surface with the brushes correctly adjusted.
3.4 Work parameters
The work parameters represent the information necessary to choose
the most suitable machine for the specific needs.
Parameters
Maximum theoretical productivity
2
(m /h)
Cleaning width mm
Forward speed (km/h)
Reverse speed (km/h)
Capacity of debris collection bin
(l)
Filtering surface (m²)
Length of central brush (mm)
Diameter of central brush (mm)
Diameter of side brushes (mm)
Brush material*
*: on request, brushes made from different materials can be fitted for
particular applications: contact the Manufacturer or dealer.
4

Safety parameters

4.1 Relevant technical regulations
The machine has been designed in accordance with community
regulations on machine safety.
4.2 Residual risks
In normal working conditions, there are no residual risks.
There are, however, residual risks always present during normal
working conditions exclusively in danger zones where access is
prevented by means of fixed or interblocked guards.
These guards must under no circumstances be removed while the
machine is in operation. Guards on transmission components may
be temporarily removed in order to carry out adjustments or routine
or extraordinary maintenance (for extraordinary maintenance,
ET
STH
5.5 ***
12V 250W ***
12V 20Ah
3.6 ***
hydraulic Electr. Mot.
*** 1100
*** 1350
*** 24 V DC
*** 3÷3.5
No. 2
***
12V and
140 Ah
***
24V - 10A
***
24V 300W
***
24V 120W
12V 40W 24V 60W
*** 24V 600W
12V 250W 24V 250W
12% 12%
5000
1100
5,5
3
50
3
690
260
400
PPL
always contact a professional service centre). The residual risks
generated under these conditions may be eliminated by adopting
certain procedures. When using the machine, the operator must be
seated in the driving position within reach of all operating controls
and with an adequate view of the path of the machine in order to
avoid impact with obstacles (danger of tipping over) and people
(injury to persons). The dust contained in the debris collection bin or
captured by the air filter may be damaging to persons affected by
chronic respiratory diseases. These persons must use suitable
respiratory P.P.D..
4.3 Noise
Guaranteed soud power level LwA 87 dB
4.4 Vibrations
The vibrations produced are minimal and do not represent a source
of danger for the operator. The levels have, however, been
determined in accordance with ISO 5349.
4.5 Degree of protection of electric machines
(IP)
Degree of protection against solid foreign bodies
(protected against dust)
Degree of protection against water (protected against
splashes of water)
4.6 Admissible environmental values
Admissible environmental values
Admissible operating
temperatures
Variations in ambient
temperature
Relative humidity range
Vibrations
The machine may also be operated out of doors providing the
surface is asphalted, concreted or similar and dry.
IMPORTANT!: If the machine is used out of doors, the operator
must wear suitable clothing to protect from excessive cold or heat.
The machine may not be used in areas with an
explosive atmosphere
components or equipment designed to operate in an
explosive atmosphere must be indicated with the
(ATEX) mark in accordance with EN 60079-14 (CEI 31-
33) "Electrical
atmospheres - Part 14: Electrical installations in
hazardous areas (other than mines)".
Use of machines with internal combustion engine in
closed or poorly ventilated environments (e.g.
greenhouses, warehouses, workshops, stalls, vertical
covered silos, etc) and the resulting combustion
fumes given off from the exhaust represent a risk of
intoxication and may cause injury or death.
4.7 Guards
All dangerous areas are closed with guards and protective devices
fixed to the chassis with screws making all hazardous areas
inaccessible to the operator. There is one mobile guard. The top
cowling on which the seat is mounted can be opened, but opening is
controlled by safety devices.
4.8 Safety devices
The machine is equipped with a double safety device under the seat
on the top cowling known as the "operator present" safety device. It
stops the engine when the operator voluntarily or involuntarily
vacates the seat and prevents the engine from being started up
unless the operator is in position on the seat where he has access to
all the machine controls. Both sensors must be working correctly to
allow the machine to start up.
3
3
-10° C ÷ 50° C
(50° F ÷ 113° F)
Max. 1.1° C / min.
(Max 2° F / min.)
75% or less
≤ 0.5 G
Machinery and relative
apparatus for explosive gas