Tools And Requirements; Installation - PLYMOVENT EDS Instrucciones Para El Uso

Sistema diluter por filtración general

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

WARNING

Fire hazard! Never use the product for:

- extracting and/or filtering flammable, glowing or

burning particles or solids or liquids

- extracting and/or filtering of aggressive fumes (such

as hydrochloric acid) or sharp particles

- extracting of aggressive fumes (such as hydrochloric

acid) or sharp particles

- extracting and/or filtering dust particles which are

released when welding surfaces treated with primer

- sucking cigarettes, cigars, oiled tissues, and other

burning particles, objects, and acids

WARNING

Never use the product for:

- oil mist

- paint mist

- extraction of hot gases (more than 45°C/113°F

continuously)

- explosive environments or explosive substances/

gases

Note: this list is not all-embracing.

Installation

- The installation of this product is exclusively reserved to well

authorised, trained and qualified engineers.

- Electric connection to be executed in accordance with local

requirements. Ensure compliance with the EMC regulatory

arrangements.

- During installation, always use Personal Protective Equipment

(PPE) to avoid injury. This also applies for persons who enter

the work area during installation.

- Use sufficient climbing gear and safety guards when working

on a higher level than 2 meter (6.5 ft) (local restrictions may

apply).

- Never install the product in front of entrances and exits which

must be used for emerency services.

- Mind any gas and water pipes and electric cables.

- Make sure the wall, ceiling or support system are strong

enough to carry the product.

- Ensure the workspace is well illuminated.

- Use common sense. Stay alert and keep your attention to your

work. Do not install the product when you are under the

influence of drugs, alcohol or medicine.

- Make sure that the workshop, in the vicinity of the product,

contains sufficient approved fire extinguishers.

- Air containing particles such as chromium, nickel, beryllium,

cadmium, lead etc., which is a health hazard, should never be

recycled. This air must always be brought outside the working

area.

Use

- Inspect the product and check it for damage. Verify the

functioning of the safety features.

- During use, always use Personal Protective Equipment (PPE)

to avoid injury. This also applies for persons who enter the

work area.

- Check the working environment. Do not allow unauthorised

persons to enter the working environment.

- Protect the product against water and humidity.

- Make sure the room is always sufficiently ventilated; this

applies especially to confined spaces.

Service, maintenance and repairs

- Observe the maintenance intervals given in this manual.

Overdue maintenance can lead to high costs for repair and

revisions and can render the guarantee null and void.

- During service, maintenance and repair jobs, always use

Personal Protective Equipment (PPE) to avoid injury. This also

applies for persons who enter the work area.

- Always use tools, materials, lubricants and service techniques

which have been approved by the manufacturer. Never use

worn tools and do not leave any tools in or on the product.

- Safety features which have been removed for service,

maintenance or repairs, must be put back immediately after

0507340050/010111/D EDS

finishing these jobs and it must be checked that they still

function properly.

- Use sufficient climbing gear and safety guards when working

on a higher level than 2 meter (6.5 ft) (local restrictions may

apply).

ATTENTION

Service, maintenance and repairs should only be

performed in accordance with directive TRGS 560 by

authorised, qualified and trained persons (skilled)

using appropriate work practices.

WARNING

Before carrying out service, maintenance and/or

repair jobs:

- fully disconnect the machine from the mains

- disconnect compressed air supply

WARNING

Always wear face mask and gloves during filter

exchange/cleaning.

Industrial vacuum cleaner used during service and

maintenance should meet dust class H according to EN

60335-2-69.

INSTALLATION

4.1

Positioning

The EDS can be mounted on the floor or on a platform. Make

sure the outlet nozzles can be directed to the welding fume layer

without obstruction.

Depending on the circumstances, it might be necessary to use

a longer or shorter duct than the 1,5 m (5 ft) one which is

standard supplied.

Make sure there is sufficient space (min. 750 mm/2.5

ft) above the filter unit in view of filter exchange.

•

Refer to Fig. II on page 75 for positioning examples.

4.2