Neckjet And Backjet Operation (If Equipped); Effervescence Operation (If Equipped); Chromatherapy Operation (If Equipped) - Kohler K-1418 Guia Del Usuario

Neckjet and Backjet Operation (If Equipped)

- Make sure the slip cover is in place on the pillow, and the pillow is attached to the neckjet body.
NOTE: If the pillow is not properly installed the neckjets will stop. The neckjet icon and indicator bar on the user
keypad will flash. The neckjets will automatically restart when the pillow is properly installed.
- With the whirlpool operating, rotate the outer ring until the neckjet icon is flashing. Press "OK" to activate the
neckjets. The neckjet pulsing action will start at medium speed.
- To increase or decrease the neckjet pulsing action, press either the up or down arrow buttons on the keypad, while
the neckjet mode is active.
- To increase or decrease the flow volume to the neckjets, rotate the outer ring to the Flexjet mode, press "OK" to
activate the mode, and press either the up or down arrows on the keypad. This also increases or decreases the
flow to all modes.
- Rotate the outer ring until the backjet mode is flashing and press "OK". The backjet pulsing action will start at
medium speed. The backjets pulse from the bottom of the whirlpool toward the top, with water flow and pulse
action occuring from two backjets at a time.
NOTE: If the water level falls below the water level sensors, the backjets will stop. The backjet icon and indicator
bar on the user keypad will flash. The backjets will automatically restart when the water level covers the sensors.
- To increase or decrease the backjet pulsing action, press either the up or down arrow buttons on the keypad, while
the backjet mode is active.
- To increase or decrease the flow volume to the backjets, rotate the outer ring to the Flexjet mode, press "OK" to
activate the mode, and press either the up or down arrows on the keypad. This also increases or decreases the
flow to all modes.
NOTE: To activate or deactivate different modes while the neckjets and/or backjets are operating, rotate the outer
ring until the desired mode is flashing and press "OK". (Example: To turn the heater off, rotate ring until heater
icon is flashing and press "OK".
- Press "OK" while the neckjet mode is flashing, to turn off the neckjets.
- Press "OK" while the backjet mode is flashing, to turn off the backjets.

Effervescence Operation (If Equipped)

- With the whirlpool operating, rotate the outer ring until the effervescence icon is flashing. Press "OK" to activate
the effervescence ports. The effervescence action will start at the flow volume last set in the Flexjet flow mode.
- Increase or decrease the flow volume by pressing either the up or down arrow buttons on the keypad.
NOTE: The effervescence mode is intended to be a relaxing, soothing experience. The Flexjet mode, backjets and
neckjets will automatically turn off when the effervescence mode is activated. Chromatherapy may be used with
this and all modes of operation.
- Press "OK" while the effervescence mode is flashing, to turn off the effervescence ports.

Chromatherapy Operation (If Equipped)

NOTE: Chromatherapy may be used with all modes of operation. Chromatherapy may also be used when the
pump is not operating.
- Chromatherapy Cycle- When this mode is activated, the chromatherapy lights will automatically and
continuously cycle through the eight colors; white, violet, indigo blue, aqua blue, green, yellow, orange and red.
One cycle through all eight colors takes approximately one minute. Rotate the outer ring to select this mode and
press "OK" to activate it. Press "OK" while the chromatherapy mode is active, to turn off the lights.
- Chromatherapy Specific Color Selection- When this mode is activated, you may choose a specific color for the
bath. Rotate the outer ring to select this mode, press "OK" to activate and use the up/down arrows to reach the
desired color. Press "OK" while the chromatherapy mode is active, to turn off the lights.
Kohler Co.
7
A
1023249-5-