Wayne Dalton TorqueMaster Plus 9100 Instrucciones De Instalación Y Manual Del Propietario página 42

D
Measure the curved ends of the horizontal track
if you have a 12" or 15" radius horizontal track,
in FIG. 2.1. Determine center line of door. Mark vertical line
at this point, on the header wall. Raise the door slightly until
the top section reaches the highest point of travel (high
Using a level, mark this high arc point of travel on the header
wall, intersecting the vertical center line, as shown in FIG.
2.2 through 2.3. Hold the wall bracket's bottom edge to the
appropriate 1/2" - 1" (room permitting) above of the high
arc line and centered on the vertical
2.3. Spot the wall brackets mounting holes on the header
wall and then refer to your garage door operator manual for
pre-drilling and securing the
OPERATOR HOOK-UP CHARTS, refer to referenced illustrations
in FIG. 2.4 through FIG. 2.5 for correct arm hook-up from
trolley to operator bracket.
NOTE: Refer to your operator manual for specific details on
how to assembly the curved and straight arm, as shown in
FIG. 2.4 through FIG. 2.5.
NOTE: Depending on your setup, you may or may not have to
cut straight arm to accomplish trolley settings, as shown in
FIG. 2.4 through FIG. 2.5.
Align hole in the appropriate arm with holes in operator
bracket tabs, as shown in FIG. 2.6. Insert 5/16" x 1-1/4"
clevis pin, making sure hole in clevis pin is outside of second
tab of operator bracket. Insert hairpin cotter into clevis pin
hole and spread hairpin cotter to ensure it will secure
assembly, as shown in FIG. 2.6.
OPERATOR HOOK-UP CHART STANDARD LIFT FOR 12" RADIUS
OPERATOR MODELS TYPE OF ARM BEING USED
QUANTUM/CLASSIC CURVED / STRAIGHT
LINEAR STRAIGHT / CURVED
LIFTMASTER
CURVED / STRAIGHT
(SEARS)
GENIE CURVED / STRAIGHT
OPERATOR HOOK-UP CHART STANDARD LIFT FOR 15" RADIUS
OPERATOR MODELS TYPE OF ARM BEING USED
QUANTUM/CLASSIC CURVED / STRAIGHT
LINEAR STRAIGHT / CURVED
LIFTMASTER
CURVED / STRAIGHT
(SEARS)
GENIE CURVED / STRAIGHT
42
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
Trolley Installation for
Standard Lift
to determine
as shown
arc).
line, as shown in FIG.
wall bracket to header. Using the
REF. ILLUSTRATIONS
ABOVE
FIG. 2.5
FIG. 2.4
FIG. 2.5
FIG. 2.5 OR FIG. 2.4
REF. ILLUSTRATIONS
ABOVE
FIG. 2.5
FIG. 2.4
FIG. 2.5
FIG. 2.5 OR FIG. 2.4
DETERMINE THE WAYNE DALTON
TRACK RADIUS BEING USED:
HORIZONTAL
TRACK
12" OR 15"
FIG. 2.1
TYPICAL 1/2" - 1" ABOVE HIGH ARC
TORQUEMASTER
HIGH ARC
COUNTERBALANCE
LINE
VERTICAL
CENTER LINE
FROM
STEP 12
HEADER
FIG. 2.3
STRAIGHT
ARM
HAIRPIN
COTTER
OPERATOR
BRACKET
OPERATOR
BRACKET TABS
5/16" X 1-1/4"
CLEVIS PIN
DOOR ARM
LEVEL
HIGH ARC
TOP
SECTION
FIG. 2.2
®
STRAIGHT
CURVED
ARM
CUT STRAIGHT
ARM TO
ACCOMPLISH
TROLLEY
SETTING
FIG. 2.4
CURVED
ARM
CUT STRAIGHT
ARM TO
ACCOMPLISH
TROLLEY
SETTING
FIG. 2.5
DOOR
ARM
FIG. 2.6
HAIRPIN COTTER
(OUTSIDE OF OPERATOR
TOP VIEW
BRACKET TAB)
OPERATOR BRACKET TABS
ARM