MIRKA AOS130-B Manual De Instrucciones página 55

NOTICE: To receive any expressed or implied warranty, tool must be repaired by an authorized Mirka Service Center. The following
general service instructions provided are for use after completion of the warranty period.
DISASSEMBLY INSTRUCTIONS
Changing Grips:
1. The (29) Grip has two "tabs" that wrap around the body of the
sander under the inlet and exhaust. With a small screwdriver
pick out one of the "tabs" of the Grip, and then continue to go
underneath the Grip with the screwdriver and pry the grip off
the sander. To install a new Grip, hold the Grip by the tabs
so that they face outward, align the Grip and slide it under
the (27) Throttle Lever then press the Grip down until it seats
onto the top of the sander. Make sure the two "tabs" seat
under the inlet and exhaust.
Motor Disassembly:
1. Remove the (44) Pad from the machine by removing the
four (42) Screws using the (45) 2.5 mm Hex Wrench. Lightly
secure tool in a vise using the (MPA0026) T-7 Soft Collar
or padded jaws with the bottom of the pad facing upward.
Remove the (43) Screw and four (42) Screws using the (45)
2.5 mm Hex Wrench. Be careful to observe and collect the
optional (25 or 26) Spacer(s) found between the (24) Spindle
Assembly and the (41) Pad Backing.
2. Take the machine out of the vise and take off the Soft Collar.
Remove the (34) Shroud Seal if applicable. Remove the four
(31) Screws and the (32) Washers from the (33) Housing
using the (45) 2.5 mm Hex Wrench and remove the (39) Mini
Pad Supports. Lightly re-secure the tool in a vise using the
(MPA0026) T-7 Soft Collar or padded jaws with the (12) Lock
Ring facing upward.
3. Remove the (12) Lock Ring with the (MPA0025) T-6 Motor
Lock Ring Wrench/Spindle Puller Tool. Remove the (11)
O-Ring from the Lock Ring and set it aside. The motor as-
sembly can now be lifted out of the (33) Housing.
4. Remove the (1) Retaining Ring from the groove in the (13)
Shaft Balancer and the (5) O-Ring from the (4) Cylinder.
5. Remove the (3) Rear Endplate. This may require setting the
Rear Endplate on the (MPA0416) Bearing Separator and
lightly pressing the shaft through the (2) Bearing and Rear
Endplate. Remove the (4) Cylinder and the (6) Rotor with
the five (7) Vanes from the (13) Shaft Balancer. Remove the
(8) Key, then press off the (9) Front Endplate with the (10)
Bearing. It may be necessary to remove the Bearing with a
Bearing Separator if it came out of the Front Endplate and
stuck to the shaft of the Shaft Balancer.
6. Remove and discard the (71) Dust Shield from the (13) Shaft
Balancer.
7. Remove the Bearing(s) from the Endplates by using the
(MPA0036) T-8 Bearing Removal Tool to press out the Bear-
ings.
Shaft Balancer and Spindle Disassembly:
1. Grip the shaft end of the (13) Shaft Balancer in a padded
vise. With a thin screwdriver pick out the slotted end of the
(23) Retaining Ring and prise it out.
2. Screw the female end of the (MPA0102) T-12 5/16-24 to M6
x 1P Adapter into the male end of the (MPA0025) T-6 Motor
Lock Ring Wrench/Spindle Puller Tool. Screw the Service
Wrench Assembly into the (24) Spindle Assembly until hand
tight. Apply gentle heat from a propane torch or hot air gun to
the large end of the (13) Balancer Shaft until it is about 100
°C (212°F) to soften the adhesive. Do not over-heat. Remove
the Spindle Assembly by using the slider to give sharp
MIRKA 10,000 OPM 75 mm x 100
mm )3 in x 4 in.( ORBITAL SAND-
ER SERVICE INSTRUCTIONS
outward blows to the Spindle. Allow the Spindle and Shaft
Balancer to cool.
3. Remove the (17) Retaining Ring from the (24) Spindle
Assembly. Use the (MPA0416) small Bearing Separator
to remove the (18) Bearing, (19) Shim, (20) Bearing, (21)
Shim,(72) Dust Shield and the (22) Washer from the Spindle
Assembly. Discard Dust Shield.
4. The AirSHIELD™ components are held in place by a light
press fit against the (16) Retainer. These components can
be damaged during removal and may need to be replaced if
removed. To remove the Retainer, use an O-Ring pick or a #8
sheet metal screw to grip and pull out the Retainer. Remove
the (15) Valve and (14) Filter from the bore in the (13) Shaft
Balancer. If the Retainer and Valve were not damaged, they
can be reused. However, the filter should be replaced on
re-assembly.
Housing Disassembly:
1. For Non Vacuum (NV) and Central Vacuum (CV) machines,
follow steps A – D below (unless otherwise noted). For Self
Generated Vacuum (DB) machines disregard steps A – F and
move onto step G below.
A. Unscrew the (48) Muffler Housing from the (33) Housing.
B. Remove the (46) Muffler from the cavity of the (48) Muffler
Housing.
C. Remove the (47) Plate and second (46) Muffler from the
exhaust port of the (33) Housing. For non-vacuum machines,
move onto step 2. For central vacuum machines, move onto
E – G.
For CV exhaust machines:
D. Remove the (68) Screw, (67) Washer and (66) Nut.
E. Press downward on the swivel end of the (57) Ø 1 in./28 mm
OS SuperVAC™ CV Swivel Exhaust Assembly or the (58)
Ø ¾ in./19 mm SuperVAC™ CV Swivel Exhaust Assembly,
releasing the tab on the end of the exhaust assembly from
the (54) Snap-In Exhaust Adapter.
F. Work off the (54) Snap-In Exhaust Adapter (for central
vacuum machines). Work off the (53) Snap-In Vacuum Cover
Plate (for non-vacuum machines). Move on to step 2.
For DB exhaust machines:
G. Unscrew the (55) DB Retainer Assembly with an (MPA0849)
8 mm Hex Key Wrench. Remove the two (56) O-Rings. Take
off the (57) Ø 1 in./28 mm DB Swivel Exhaust Assembly or
the (58) Ø ¾ in./19 mm Hose DB Swivel Exhaust Assembly.
H. Work off the (54) Snap-In Exhaust Adapter.
3. Set the (37) Speed Control to the midway position and
remove the (38) Retaining Ring. The Speed Control will now
pull straight out. Remove the (36) O Ring.
4. Unscrew the (52) Inlet Bushing Assembly from the (33) Hous-
ing. Remove the (51) Spring, (50) Valve, (49) Seat, (35) Valve
Stem with the (36) O-Ring.
5. Press out the (28) Spring Pin from the (33) Housing and
remove the (27) Lever.
ASSEMBLY INSTRUCTIONS
Note: All assembly must be done with clean dry parts and all
bearings are to be pressed in place using the correct tools and
procedures as outlined by the bearing manufacturers.
Housing Assembly:
1. Install the (27) Throttle Lever into the (33) Housing with the
52