Starting And Stopping - Ryobi RBC430SESD Manual De Utilización

RBC430SBD
See fi gure 12.
Engine lubricant has a major infl uence on engine
performance and service life. For general, all-temperature
use, SAE 20W-50 is recommended. Always use a 4-stroke
motor lubricant that meets or exceeds the requirements.
NOTE: Non-detergent or 2-stroke engine lubricants will
damage the engine and should not be used.
To add engine lubricant:
■ Remove the cap and seal from lubricant bottle
provided.
■ Screw the funnel to the lubricant bottle, and then
remove the small red cap from the funnel.
■ Unscrew the oil cap/dipstick and remove.
■ Add the entire bottle of engine lubricant through oil fill
hole.
■ Reinstall the oil cap/dipstick and secure.
To check engine lubricant level:
■ Set engine on a flat surface unscrew the oil cap
dipstick and remove.
■ Wipe the dipstick clean and re-seat in hole; do not re-
screw.
■ Remove dipstick again and check lubricant level.
Lubricant level should fall within the hatched area on
the dipstick.
■ If level is low, add engine lubricant until the fluid level
rises to the upper portion of the hatched area on the
dipstick.
■ Replace and secure the oil cap/dipstick.
CAUTION
Do not overfi ll. Overfi lling the crankcase may cause
-excessive smoke and engine damage.

STARTING AND STOPPING

To start a cold engine:
RBC430SESD
See fi gure 9a.
NOTE: Lay the product on the ground. Ensure the cutting
means will not contact anything when it starts to rotate.
1. Press the primer bulb 10 times.
NOTE: After the 7th press, the fuel should be visible
in the primer bulb. If not, continue pressing until the
fuel is visible.
2. Set the choke lever to the
3. Hold down the throttle lock and then squeeze the
throttle trigger. Keep the throttle trigger squeezed
completely following steps 3 to 7. Pull the starter grip
English (Original instructions)
choke position.
28
until the engine attempts to start. Do not pull the starter
grip more than 4 times.
4. Set the choke lever to the
5. Pull the starter grip until the engine starts. Do not pull
the starter grip more than 6 times.
NOTE: If the engine does not start, repeat the
procedure from step 2.
6. Allow engine to warm up for 10 seconds.
7. Set the choke lever to the
RBC430SBD
See fi gure 7a.
NOTE: Lay the product on the ground. Ensure the cutting
means will not contact anything when it starts to rotate.
1. Press the primer bulb 10 times.
NOTE: After the 7th press, the fuel should be visible
in the primer bulb. If not, continue pressing until the
fuel is visible.
2. Set the choke lever to the
3. Hold down the throttle lock and then squeeze
the throttle trigger. Lock the throttle in position by
depressing the throttle interlock button. Hold the foam
handle tightly with left hand and pull the starter grip
upwards with right hand in a quick, fi rm and consistent
motion until the engine attempts to start. Do not pull
the starter grip more than 4 times.
4. Set the choke lever to the
5. Pull the starter grip until the engine starts. Do not pull
the starter grip more than 6 times.
NOTE: If the engine does not start, repeat the
procedure from step 2.
6. Allow the engine to run for 10 seconds.
7. Set the choke lever to the
To start a warm engine:
RBC430SESD
See fi gure 9b.
NOTE: Lay the product on the ground. Ensure the cutting
means will not contact anything when it starts to rotate.
1. Press the primer bulb 10 times.
2. Set the choke lever to
3. Hold down the throttle lock and then squeeze the
throttle trigger completely and pull the starter grip until
the engine starts.
RBC430SBD
See fi gure 7b.
NOTE: Lay the product on the ground. Ensure the cutting
means will not contact anything when it starts to rotate.
1. Press the primer bulb 10 times.
2. Set the choke lever to
3. Hold down the throttle lock and then squeeze
choke position.
position.
choke position.
choke position.
position.
position.
position.