Manuales relacionados para Allied Telesis AT-GS900/5E
Resumen de contenidos para Allied Telesis AT-GS900/5E
- Página 1 Gigabit Ethernet ® Switches AT-GS900/5E AT-GS900/8E Installation Guide PN 613-000551 Rev A...
- Página 2 Allied Telesis, Inc. has been advised of, known, or...
-
Página 3: Electrical Safety And Emissions Standards
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. - Página 4 Electrical Safety and Emissions Standards Translated Safety Statements Important: Appendix B contains translated safety statements for installing this equipment. When you see the , go to Appendix B for the translated safety statement in your language. Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn sehen, schlagen Sie in Anhang B den übersetzten Sicherheitshinweis in Ihrer Sprache nach.
-
Página 5: Tabla De Contenido
Electrical Safety and Emissions Standards ........................3 Preface ....................................7 How This Guide is Organized .............................. 7 Document Conventions ............................... 8 Contacting Allied Telesis ..............................9 Online Support ................................9 Email and Telephone Support ............................9 Returning Products...............................9 For Sales or Corporate Information ..........................9 Chapter 1 Product Description ............................... - Página 6 Contents Appendix B Translated Safety Statements ............................37...
-
Página 7: Preface
Appendix A, ”Technical Specifications” on page 34 Appendix B, ”Translated Safety Statements” on page 37 This preface contains the following sections: “How This Guide is Organized” on page 7 “Document Conventions” on page 8 “Contacting Allied Telesis” on page 9... -
Página 8: Document Conventions
Preface Document Conventions This document uses the following conventions to highlight important information: Note Notes provide additional information. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. -
Página 9: Contacting Allied Telesis
Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions. Email and For Technical Support via email or telephone, refer to the Allied Telesis web site: http://www.alliedtelesis.com. Select your country from the list Telephone displayed on the website. -
Página 10: Product Description
Chapter 1 Product Description This chapter contains the follows sections: “Overview” on page 11 “Key Features” on page 13 “Standards” on page 13 “Hardware Feature Description” on page 14 “A Few Ethernet Switching Basics” on page 17 “Network Topologies” on page 20... -
Página 11: Overview
Connecting to other Ethernet switches so that they can be part of a larger Ethernet network. Maximizing your existing network by providing full-duplex operation over a twisted pair port. Figure 1 illustrates the front panel of the AT-GS900/5E switch. 1000 LINK 10/100 LINK AT-GS900/5E... - Página 12 Chapter 1: Product Description Figure 3 illustrates the back panel of the AT-GS900/5E switch. 12VDC 1037 Figure 3. AT-GS900/5E Back Panel Figure 4 illustrates the back panel of the AT-GS900/8E switch. 12VDC 1032 Figure 4. AT-GS900/8E Back Panel The AT-GS900/5E switch features five 10/100/1000 Mbps ports with RJ-45 connectors.
-
Página 13: Key Features
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Key Features The AT-GS900/xE Series switch has the following key features: Five or eight 10/100/1000 Mbps twisted pair ports with RJ-45 connectors System and port LEDs Auto MDI/MDI-X on all 10/100/1000 Mbps twisted pair ports Support half- or full-duplex mode on all 10/100/1000 Mbps twisted pair ports Auto-Negotiation (IEEE 802.3u-compliant) -
Página 14: Hardware Feature Description
Chapter 1: Product Description Hardware Feature Description The below sections describe the hardware features of the AT-GS900/xE Gigabit Ethernet switch: Five or eight 10/100/1000 Mbps twisted pair ports System and port LEDs DC power jack 10/100Base-TX The AT-GS900/xE Gigabit Ethernet switch features sixteen twisted pair ports. -
Página 15: Leds
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Type of Cabling For 10 Mbps operation, Category 3 or better 100 ohm shielded or unshielded twisted pair cabling is required. For 100 Mbps operation, Category 5 and Enhanced Category 5 (5E) 100 ohm shielded or unshielded twisted pair cabling is required. -
Página 16: Dc Power Connector
Chapter 1: Product Description DC Power The AT-GS900/xE Gigabit Ethernet switch has a single DC power jack on the back panel. Refer to Appendix A, “Technical Specifications” on Connector page 34, for the input voltage specifications. To power ON or OFF the switch, you connect or disconnect the power adapter. -
Página 17: A Few Ethernet Switching Basics
AT-GS900/xE Gigabit Ethernet Switch Installation Guide A Few Ethernet Switching Basics An Ethernet switch interconnects network devices, such as workstations, printers, routers, and other Ethernet switches, so that they can communicate with each other by sending and receiving Ethernet frames. MAC Address Every hardware device on your network has a unique MAC address. -
Página 18: Duplex Mode
Note Since the ports on the AT-GS900/xE switches operate in Auto- Negotiate mode only, the end nodes connected to the AT-GS900/5E or AT-GS900/8E switch must also be configured to operate in the Auto-Negotiate mode. If an end node is configured to a specific duplex in a manual mode, it will not respond to the Auto-Negotiate protocol from the AT-GS900/5E or AT-GS900/8E switch. -
Página 19: Back Pressure And Flow Control
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Back Pressure To maintain the orderly movement of data between the end nodes, an Ethernet switch may periodically need to signal an end node to stop and Flow Control sending data. This can occur under several circumstances. For example, if two end nodes are operating at different speeds, the switch, while transferring data between the end nodes, might need to instruct the faster end node to stop transmitting data to allow the slower end node to catch... -
Página 20: Network Topologies
Chapter 1: Product Description Network Topologies This section illustrates two network topologies that you can create with the AT-GS900/xE switches: a power workgroup and collapsed backbone. Both types of topologies are described below. Power The topology shown in Figure 5 is commonly referred to as a power workgroup topology. -
Página 21: Collapsed Backbone
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Collapsed In the topology illustrated in Figure 6, an AT-GS900/8E connects Fast Ethernet switches that have Gigabit Ethernet uplinks. This type of topology Backbone is often referred to as a collapsed backbone topology. The switch functions as the focal point of the network and transfers an Ethernet frame between the Fast Ethernet switches only when the destination end node for the frame is on a different switch than the end node that originated the frame. -
Página 22: Installation
Chapter 2 Installation This chapter contains the following sections: “Reviewing Safety Precautions” on page 23 “Selecting a Site for the Switch” on page 24 “Planning the Installation” on page 25 “Unpacking the Switch” on page 26 “Installing the Switch on a Table or Desktop” on page 27 “Wall-Mounting the Switch”... -
Página 23: Reviewing Safety Precautions
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Reviewing Safety Precautions Please review the following safety precautions before you begin to install the switch or any of its components. Refer to “Translated Safety Statements” on page 37 for translated safety statements in your language. Warning To prevent electric shock, do not remove the cover. -
Página 24: Selecting A Site For The Switch
Chapter 2: Installation Selecting a Site for the Switch Observe the following requirements when choosing a site for the AT-GS900/xE Gigabit Ethernet switch: If you are installing the switch on a table, be sure that the table is level and secure. The power outlet for the switch should be located near the unit and should be easily accessible. -
Página 25: Planning The Installation
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Planning the Installation Table 2 contains the cabling specifications for the twisted pair ports. Table 2. Twisted Pair Cabling and Distances Maximum Speed Type of Cable Operating Distance 10 Mbps Category 3 or better 100-ohm 100 m (328 ft) shielded or unshielded twisted pair cable... -
Página 26: Unpacking The Switch
Chapter 2: Installation Unpacking the Switch To unpack an AT-GS900/xE switch, perform the following procedure: 1. Remove all components from the shipping package. Note Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesis. -
Página 27: Installing The Switch On A Table Or Desktop
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Installing the Switch on a Table or Desktop To install the AT-GS900/xE switch on a table or desktop, perform the following procedure: 1. Remove all the items from the packaging and store the packaging material in a safe place. - Página 28 Chapter 2: Installation Warning Power cord is used as a disconnection device: To de-energize equipment, disconnect the power cord. 6. Verify that the POWER LED is green. If the LED is OFF, refer to “Troubleshooting” on page 33 for instructions. Note The switch perform a self-diagnostic test upon power up.
-
Página 29: Wall-Mounting The Switch
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Wall-Mounting the Switch The AT-GS900/xE switch can be mounted horizontally on a wall using the two keyhole slots in the bottom of the switch. To mount an AT-GS900/xE switch onto a wall, perform the following procedure: 1. - Página 30 Chapter 2: Installation 7. Position and hang the switch onto the wall using the two keyhole slots located in the bottom of the switch, as illustrated in Figure 9. 1042 Figure 9. Wallmounting an AT-GS900/8E Switch 8. Make sure that the switch is securely mounted onto the wall. The switch is now ready for cabling.
-
Página 31: Cabling The Switch
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Cabling the Switch To connect the twisted pair cables to the ports on the AT-GS900/xE switch, perform the following procedure: 1. Connect the twisted pair data cables to the RJ-45 ports on the switch, as shown in Figure 10. -
Página 32: Powering On The Switch
Chapter 2: Installation Powering On the Switch To apply power to the AT-GS900/xE switch, perform the following procedure: 1. Apply DC power to the switch by plugging the DC power connector from the external power adapter to the DC power jack on the back panel of the unit, as shown in Figure 11. -
Página 33: Troubleshooting
If you are still unable to resolve the problem after following the instructions in this chapter, contact Allied Telesis Technical Support for assistance. Refer to “Contacting Allied Telesis” on page 10. Check the POWER LED on the front of the switch. If the LED is OFF,... -
Página 34: Appendix A
Appendix A Technical Specifications Physical Specifications Dimensions: (W x D x H) AT-GS900/5E 140 mm x 101 mm x 31 mm (5.5 in x 4.0 in x 1.2 in) AT-GS900/8E 195 mm x 114 mm x 36 mm (7.7 in x 4.5 in x 1.4 in) -
Página 35: Safety And Electromagnetic Emissions Certifications
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Safety and Electromagnetic Emissions Certifications FCC Class A, CISPR 22 Class A, EN55022 Class A, C-TICK, CE Immunity EN55024 Electrical Safety UL 60950 ( ), EN60950 (TUV) Compliance Standards IEEE 802.3 – Ethernet IEEE 802.3i – 10Base-T IEEE 802.3u –... -
Página 36: Rj-45 Twisted Pair Port Connectors
Appendix A: Technical Specifications RJ-45 Twisted Pair Port Connectors This section lists the connectors and connector pinouts for the AT-GS900/xE Gigabit Ethernet switch and its components. Figure 12 illustrates the pin layout to an RJ-45 connector and port. Figure 12. RJ-45 Connector and Port Pin Layout Table 3 lists the RJ-45 pin signals when a twisted pair port is operating in the MDI configuration. - Página 37 Appendix B Translated Safety Statements Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Importante: Este apéndice contiene traducciones en múltiples idiomas de los mensajes de seguridad incluidos en esta guía.
- Página 38 Appendix B: Translated Safety Statements Laser Safety Notices Warning: Class 1 Laser product. Warning: Do not stare into the laser beam. Electrical Safety Notices Warning: To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician.
- Página 39 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Warning: Check to see if there are any exposed copper strands coming from the installed wire. When this installation is done correctly there should be no exposed copper wire strands extending from the terminal block. Any exposed wiring can conduct harmful levels of electricity to persons touching the wires.
- Página 40 Use dedicated power circuits or power conditioners to supply reliable electrical power to the device. Warning: The chassis may be heavy and awkward to lift. Allied Telesis recommends that you get assistance when mounting the chassis in an equipment rack.
- Página 41 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Telecommunications Compliance Notices Warning: When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electronic shock, and injury to persons, including the following: Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub in a wet basement or near a swimming pool.
- Página 42 Appendix B: Translated Safety Statements Lasersicherheitshinweise Achtung: Laserprodukt der Klasse 1. Achtung: Blicken Sie nicht in den Laserstrahl. Elektrische Sicherheitshinweise Achtung: Um Stromschläge zu vermeiden, darf die Abdeckung nicht entfernt werden. Die Ausrüstung enthält keine benutzerwartbaren Teile. Diese Einheit führt gefährliche Spannungen und sollte nur durch einen ausgebildeten und qualifizierten Techniker geöffnet werden.
- Página 43 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Achtung: Nicht mehr als die empfohlene Kabellänge abisolieren. Durch das Abisolieren von mehr als der empfohlenen Länge können gefährliche blanke Drähte aus dem Anschlussblock hervorragen. Achtung: Beim Installieren dieser Ausrüstung ist stets darauf zu achten, dass die Rahmenerdung zuerst angeschlossen und zuletzt abgetrennt wird.
- Página 44 Zur zuverlässigen Stromversorgung des Geräts sollte ein dedizierter Stromkreis oder Netzfilter und Stabilisator (Power Conditioner) verwendet werden. Achtung: Das Chassis kann schwer und schwierig zu heben sein. Allied Telesis empfiehlt, bei der Rackmontage des Chassis Hilfspersonal heranzuziehen. Achtung: Sehen Sie nicht direkt auf die Enden der Faseroptikkabel und inspizieren Sie die Kabelenden nicht mit einer optischen Linse.
- Página 45 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Telekommunikationskonformitätshinweise Achtung: Bei der Verwendung Ihrer Telefonausrüstung sollten zur Reduzierung der Brand-, Stromschlag und Verletzungsgefahr stets grundsätzliche Sicherheitsrichtlinien, einschließlich der folgenden, befolgt werden: Verwenden Sie dieses Produkt nicht in der Nähe von Wasser, zum Beispiel in der Nähe einer Badewanne, einer Waschschüssel, eines Spülbeckens, eines Waschbottichs, in einem nassen Kellerraum oder in der Nähe eines Schwimmbads.
-
Página 46: Avisos De Seguridad Láser
Appendix B: Translated Safety Statements Avisos de seguridad láser Atención: Producto láser de clase 1. Atención: No mire el rayo láser. Avisos de seguridad eléctricas Atención: Para evitar la electrocución, no quite la tapa. La unidad no contiene piezas que pueda reparar el usuario. Esta unidad contiene tensiones peligrosas y sólo la debe abrir un técnico convenientemente formado y cualificado. - Página 47 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Atención: Cuando instale el equipo, asegúrese de instalar primero la conexión a tierra del bastidor y de desconectarla en último lugar. Atención: Compruebe si hay algún hilo de cobre al descubierto que proceda del cable instalado.
- Página 48 Utilice circuitos de alimentación dedicados o acondicionadores de alimentación para suministrar energía eléctrica fiable al dispositivo. Atención: El chasis puede ser pesado y difícil de levantar. Allied Telesis recomienda buscar ayuda para montar el chasis en un rack. Atención: No mire directamente los extremos del cable de fibra óptica ni los inspeccione con una lente óptica.
-
Página 49: Avisos De Conformidad De Telecomunicaciones
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Avisos de conformidad de telecomunicaciones Atención: Cuando utilice su equipo telefónico, deberá adoptar las siguientes precauciones de seguridad básicas para reducir el riesgo de incendio, descarga electrónica y lesiones: No utilice este producto en zonas húmedas; por ejemplo, cerca de una bañera, un lavabo o un fregadero, en un sótano húmedo o cerca de una piscina. - Página 50 Appendix B: Translated Safety Statements Avis de sécurité laser Avertissement: Produit laser de classe 1. Avertissement: Ne pas observer directement le rayon laser. Avis de sécurité électrique Avertissement: Pour éviter tout risque d’électrocution, ne pas déposer le capot. L’appareil ne contient aucun composant réparable par l’utilisateur. Il est exposé à des tensions dangereuses et ne doit être ouvert que par un technicien compétent et qualifié.
- Página 51 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Avertissement: Respecter les recommandations pour dénuder les fils. Un dénudage excessif risque de présenter des risques pour la sécurité en laissant le fil exposé sur le bornier après l’installation. Avertissement: Lors de l’installation de cet équipement, toujours s’assurer que la connexion de terre de la structure est installée en premier et déconnectée en dernier.
- Página 52 Utiliser des circuits d’alimentation ou des unités de conditionnement dédiés pour fournir une alimentation électrique fiable à l’équipement. Avertissement: Le châssis peut être lourd et difficile à soulever. Allied Telesis recommande de demander de l’aide pour installer le châssis dans un rack.
-
Página 53: Télécommunications - Avis De Conformité
AT-GS900/xE Gigabit Ethernet Switch Installation Guide Télécommunications – Avis de conformité Avertissement: Les précautions élémentaires de sécurité doivent être systématiquement respectées en utilisant l’équipement téléphonique pour réduire les risques d’incendie, d’électrocution et d’accident corporel, notamment: Ne pas utiliser ce produit près d’une source d’eau, telle qu’une baignoire, un lavabo, un évier ou un baquet dans un sous-sol humide ou près d’une piscine. - Página 54 Appendix B: Translated Safety Statements Indicazioni sulla sicurezza laser Avvertenza: Prodotto laser Classe 1. Avvertenza: Non fissare il raggio laser. Indicazioni sulla sicurezza elettrica Avvertenza: Per evitare scosse elettriche, non rimuovere la copertura. All'interno non sono presenti componenti utilizzabili dall'utente. Questa unità presenta voltaggi rischiosi e deve essere aperta solo da un tecnico qualificato ed esperto.
- Página 55 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Avvertenza: Quando si installa l'apparecchiatura, verificare che il collegamento di messa a terra FG (frame ground) sia installato per primo e disinstallato per ultimo. Avvertenza: Verificare che non sporgano fili di rame dai cavi installati. Se l'installazione viene effettuata correttamente, non vi sono fili di rame scoperti, sporgenti dal blocco terminale.
- Página 56 Appendix B: Translated Safety Statements Avvertenza: Rimuovere tutti gli oggetti di metallo, ad esempio anelli e orologi, prima di installare o estrarre una scheda di linea da un chassis acceso. Utilizzare circuiti di alimentazione o alimentatori dedicati per fornire energia elettrica al dispositivo in modo affidabile.
- Página 57 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Indicazioni per la conformità con le norme sulle telecomunicazioni Avvertenza: Quando si utilizza l'apparecchiatura telefonica, per ridurre il rischio di incendio, scosse elettriche e danni alle persone, è necessario seguire alcune precauzioni di base per la sicurezza, ad esempio: Non utilizzare il prodotto in prossimità...
-
Página 58: Электрическая Безопасность
Appendix B: Translated Safety Statements Лазерная безопасность Внимание: лазерный продукт, класс 1. Внимание: Не смотрите прямо в лазерный луч. Электрическая безопасность Внимание: Для предотвращения электрического шока, не снимайте кожух. Внутри нет частей, подлежащих обслуживанию пользователем. Этот устройство – под опасным напряжением и должно открываться только обученным и квалифицированным... - Página 59 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Внимание: При инсталляции оборудования, убедитесь, что заземление подключается в первую, а отключается в последнюю очередь. Внимание: Проверьте, нет ли на инсталлированных проводков на кабеле. При правильной инсталляции на терминале свободных проводков быть не должно. Открытые...
- Página 60 Для надежного питания используйте отдельные контуры питания и выравниватели энергии. Внимание: Корпус может быть тяжелым и поднять его может быть сложно. Allied Telesis рекомендует, что при установке корпуса на раме Вам необходимо обеспечить соответствующую помощь. Внимание: Не смотрите прямо на торцы волоконно-оптического кабеля и не...
- Página 61 AT-GS900/xE Gigabit Ethernet Switch Installation Guide Телекоммуникационное соответствие Внимание: При использовании телефонного оборудования, всегда следует обращать внимания на требования безопасности для снижения риска пожара, поражения током и ранения, в том числе: Не используйте оборудование рядом с водой – например ванной, раковиной или стиральным...