Publicidad
Idiomas disponibles
Idiomas disponibles
MAiNTENANCE
wArNiNg: Any maintenance must be
carried out with the machine switched off
and disconnected from the mains/battery
power supply.
Check that all safety features and guards are
operating correctly on a regular basis.
Only use this machine if all guards/safety
features are fully operational.
All motor bearings in this machine are lubricated
for life. No further lubrication is required.
Use a clean, slightly damp cloth to clean
the plastic parts of the machine. Do not use
solvents or similar products which could
damage the plastic parts.
wArNiNg: Do not attempt to clean by
inserting pointed objects through openings in
the machines casings, etc.
The machines air vents should be cleaned
using compressed dry air.
Excessive sparking may indicate the presence of
dirt in the motor or worn out carbon brushes.
20
www.evolutionpowertools.com
BruSh ChECKiNg AND/Or rEPLACEMENT
• Disconnect the machine from the power
supply.
• Place the machine on a level, secure surface.
• Unscrew and remove the two (2) brush
retaining cap screws from the motor housing.
• Withdraw the brushes.
Note: If the carbon brush is less than ¼" long,
or if there are signs of burning or damage to
the carbon or the spring, replace the brushes.
• Fit the new brushes.
• Refit the brush retaining cap screws.
• Run the machine without load for several
minutes after brush replacement. This will
aid the 'bedding in' process.
Note: If, upon checking, the brushes are found
to be still serviceable, they can be returned to
their original position. It is important that they
are replaced in the same position as they were
removed from the machine.
ENVirONMENTAL PrOTECTiON
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
local authority or retailer for recycling advice.
www.evolutionpowertools.com
EC DECLArATiON OF CONFOrMiTy
In accordance with EN ISO 17050-1:2004
The manufacturer of the product covered by this Declaration is:
Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR.
The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the
relevant provisions of the Machinery Directive and other appropriate directives as detailed below.
The manufacture further declares that the machine as detailed in this declaration, where
applicable, fulfils the relevant provisions of the Essential Health and Safety requirements.
The Directives covered by this Declaration are as detailed below:
2006/42/EC.
Machinery Directive.
2004/108/EC.
(until Apr 19th 2016) Electromagnetic Compatibility Directive.
2014/30/EU.
(starting from Apr 20th 2016) Electromagnetic Compatibility Directive.
93/68/EC.
The CE Marking Directive.
2011/65/EU.
The Restriction of the Use of certain Hazardous
Substances in Electrical Equipment (RoHS) Directive.
2002/96/EC as
The Waste Electrical and Electronic Equipment (WEEE) Directive.
amended by
2003/108/EC .
And is in conformity with the applicable requirements of the following documents:
EN60745-1:2009+A11:2010 • EN60745-2-5:2010 • EN60825-1:2007
EN55014-1:2006/+A1:2009/+A2:2011 • EN55014-2:1997/+A1:2001/+A2:2008
EN61000-3-2:2006/+A1:2009/+A2:2009 • EN61000-3-11:2000
Product Details
Description:
EVOSAW180HD 180mm (7") CIRCULAR SAW
Evolution Model No:
EVOSAW180HD1 / EVOSAW180HD2 / EVOSAW180HD2EU / EVOSAW180HD1US
Brand Name:
EVOLUTION
Voltage:
110V/230-240V/120V ~ 50/60Hz
Input:
1100W
The technical documentation required to demonstrate that the product meets the requirements
of directive has been compiled and is available for inspection by the relevant enforcement
authorities, and verifies that our technical file contains the documents listed above
and that they are the correct standards for the product as detailed above.
Name and address of technical documentation holder.
Signed:
Print: Matthew Gavins - Operations Director
Date:
01/03/16
21
EN
SAW
180HD
ES
FR
TR
Publicidad
