Nilfisk Advance SelecTrac 12 Manual De Instrucciones página 6

INTRODUCTION
This manual will help you get the most from your SelecTrac™. Read it
thoroughly before operating the machine.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized Nilfisk-
Advance Service Center, who employs factory trained service personnel, and
maintains an inventory of Nilfisk-Advance original replacement parts and acces-
sories.
Call the NILFISK-ADVANCE DEALER named below for repair parts or service.
Please specify the Model and Serial Number when discussing your machine.
NAME PLATE
The Model Number and Serial Number of your machine are shown on the
Nameplate on the machine. This information is needed when ordering repair
parts for the machine. Use the space below to note the Model Number and Serial
Number of your machine for future reference.
MODEL NUMBER
SERIAL NUMBER
UNCRATE THE MACHINE
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it
can be inspected. Contact the Nilfisk-Advance Customer Service Department
immediately to file a freight damage claim.
PREPARATION
Before each use, check the solution filter (Figure 1), lint filter (Figure 2), and spray
nozzles (Figure 3) for lodged debris.
ADDING SOLUTION
WARNING!
DISCONNECT THE POWER CORD FROM THE ELECTRICAL
OUTLET BEFORE ADDING SOLUTION.
Fill with clean solution to the level indicator, approximately 3 gallons ( 11.4 l).
CAUTION!
Solution temperature must not exceed 120°F (49°C). Use non-
foaming chemicals only and be sure to use the correct dilution
ratios.
CONTROLS
PUMP SWITCH
This is the power switch for the pump.
BRUSH MOTOR SWITCH
This is the power switch for the brush drive motor.
CARPET/UPHOLSTERY SWITCH
The position of this switch is customizes what functions the machine provides for
that type of cleaning.
ACTIVATE BRUSH/SPRAY
The function of this switch is determined by the position of the other control
switches.
CIRCUIT BREAKER
This circuit breaker keeps the brush motor from becoming overloaded.
6 - FORM NO. 56041504 / SelecTrac
All manuals and user guides at all-guides.com
OPERATION
CLEANING CARPET AND HARD FLOOR
Prepare machine (Figure 4).
Pull the machine backwards to clean. If dispensing solution, release the
"ACTIVATE" switch six inches before the end of the cleaning pass. Overlap
cleaning passes for complete coverage. Empty recovered dirty solution into a
waste drain, rinse tank, refill with properly diluted clean solution and repeat until
area is completed.
Do not allow water or foam to overflow and enter the vacuum tube
on the recovery tank. If this happens immediately shut off the
vacuum motor, unplug the machine and contact an authorized
service center.
CLEANING UPHOLSTERY
(Optional upholstery tool required)
Refer to the chart below to achieve machine performance to match application.
Locate and read the recommended fabric cleaning instruction
label. If fabric requires dry cleaning DO NOT clean with this
machine.
Before cleaning, test fabric for colorfastness. In an inconspicuous spot, rub the
area with a solution dampened clean white terry towel.
If color does not transfer to towel, the fabric should be safe to clean. Should the
color transfer to the towel, DO NOT continue.
Prepare machine. Connect upholstery attachment to machine. Solution fitting
is on the lower back side of machine. The solution recovery hose connects to
the clear lid inlet without the lint filter.
Depress upholstery tool trigger to apply solution while pulling tool with overlap-
ping paths. Run tool over cleaned area a second time without spraying solution
to recover as much solution as possible. Empty recovered dirty solution into a
waste drain, rinse tank, refill with properly diluted clean solution and repeat until
cleaning is completed.
CLEAN UP AND STORAGE
Store the machine in a cool dry place. Wind the extension cord in a circle and
hang on the cord hook provided on the machine. Be sure not to wind the cord
tighter than necessary.
Avoid prolonged exposure of machine to freezing temperatures during storage
or transporting.
MAINTENANCE
BEFORE ANY SERVICING, AVOID POSSIBLE INJURY OR
ELECTRIC SHOCK BY DISCONNECTING THE POWER CORD
FROM THE ELECTRICAL OUTLET.
Reduce the build up of chemical residue by running 8 ounces of vinegar for every
gallon of water through the machine once a week. Be sure the vinegar solution
sprays into an appropriate tub or drain. When finished, run clean water through
the machine.
Do not use vinegar solution on carpet.
Spray the solution quick disconnect fitting with silicone lubricant to prevent
sticking.
12
™
CAUTION!
CAUTION!
WARNING!
CAUTION!