Preset Functions And Operations; List Of Preset Functions - Denon DN-C680 Instrucciones De Operación

ENGLISH

7 PRESET FUNCTIONS AND OPERATIONS

(1) List of Preset Functions

¥ Functions can be preset using the buttons on the front panel. These presettings are stored in a permanent memory, so they are not
cleared even when the power is turned off.
¥ The functions shown on the table below can be preset. Set the functions according to the usage purpose to efficiently achieve even
higher quality playback.
¥ One of the preset functions can be used to display information on this set (microprocessor version).
Preset function type
Preset type
Auto cue
Auto stop
FS converter
Program 1
Program 2
Program 3
Digital output
Digital output
End monitor
E.O.M.
Next track standby
Fade in time
Fade out time
Play speed
Delay start
Play lock
Frame display
CDR disc
CDR disc
Serial remote
Switch protect
Player ID
Parallel remote
Parallel remote
Parallel remote
Parallel remote
Stereo/mono
Pos Code
Preset clear
Set information
External synchronizing signal
Frame rate
LTC time code
Protocol type
Synchronizing operation mode
Synchronizing operation time
memory mode
Synchronizing operation time
When presettings are made, the time display set with the TIME button, the play mode set with the PLAY MODE button and the finish mode
set with the FINISH MODE button at that time are stored in the memory. These modes will be set when the power is next turned on.
NOTE:
For CD-R discs without TOCs, there are no pits (signals) at the discÕ s lead in and lead out sections, so errors may occur, particularly when
searching for tracks. If an error should occur, open the disc holder, then close it and perform the operation again.
22
Description
Selection of preset type
Setting of audio startup level for auto cue function
Setting of whether or not to automatically stop the servo functions
Setting of whether or not to use the FS converter and sampling frequency
setting (when optional FS converter mounted)
Setting of whether or not to play program 1
Setting of whether or not to play program 2
Setting of whether or not to play program 3
Selection of output signal format
Selection of whether or not to output subcodes
Setting of whether or not to use the end monitor function and monitor time
setting
Setting of whether or not to display the EOM and display time setting
Setting of whether or not to standby at the next track when the STANDBY/
CUE button is pressed during playback
Fade in time setting
Fade out time setting
Standard playing speed setting
Delay start time setting
Selection of whether or not to inhibit the panel switches during playback
Selection of whether or not to display frames
Selection of whether or not to play CDR discs which do not include a TOC
Selection of whether or not to play skip tracks on CDR discs
Baud rate setting
Selection of whether or not to enable the panel switches
Selection of whether or not to set player IDs and selection of ID number
Selection of whether or not to accept parallel remote signals
Selection of whether or not to output standby tally
External control tally output signal setting
Fader start mode selection
Selection of stereo or monaural playback
Selection of whether or read Pos codes
Setting for clearing presets and setting them to the initial values
Microprocessor version display
Selection of external synchronizing signal
(When optional synchronizing kit mounted)
Selection of time code and video signal frame per second(fps)
(When optional synchronizing kit mounted)
Selection of LTC time code synchronizing operation
(When optional synchronizing kit mounted)
Selection of serial remote protocol
(When optional synchronizing kit mounted and Ò LTC time codeÓ setting is set to Ò LTC ONÓ )
Selection of synchronizing operation mode with LTC time code
(When optional synchronizing kit mounted and Ò LTC time codeÓ setting is set toÒ LTC ONÓ )
Selection of method of setting start time for synchronizing operation with LTC time code
(When optional synchronizing kit mounted and Ò LTC time codeÓ setting is set to Ò LTC ONÓ )
Selection of start time for synchronizing operation with LTC time code
(When optional synchronizing kit mounted and Ò LTC time codeÓ setting is set to Ò LTC ONÓ )
Character display
(as set upon shipment from factory)
Preset Type 1
CueDet.Ð 60db
Sleep ON
FS OFF
Program1 OFF
Program2 OFF
Program3 OFF
D.Out Pro
Subcode OFF
End Mon. 10sec
E.O.M. 10sec
NextStb.OFF
Fadein OFF
FadeOut OFF
Normal Speed
Delay OFF
PlayLock OFF
FR Disp ON
CD-R TOC
CD-R Skip OFF
9600bps
Switch ENA
PlayerlD OFF
Remote ENA
ST.Tally ON
lndex2 Tally
Fader Pause
Stereo
Pos OFF
Init. Preset
Ver. ****(* = number)
Sync OFF
29.97fps DRF
LTC OFF
Type BVW75
Chase
Auto Memory
10h00m00s00f
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38