Installation - General - Franklin Electric E-Tech Serie Manual De Uso

ENGLISH
Translation of original instructions
2.2 Other plates and markings
On the surface of the pump, there may be other plates, depending on the model,
that identify its features, compliance with rules and regulations or installation, use
and disposal provisions. See the following list.
Pay attention to the risks associated with the product installation,
maintenance and disposal.
Before installing and using the electric pump, carefully read the
instruction manual.
Appliance approved for handling cold water only intended for
human consumption.
Maximum liquid temperature for use in the home, residential,
commercial, agricultural or tertiary sector: 90°C (three-phase
versions only), 55°C (single-phase versions).
Maximum liquid temperature EXCLUSIVELY for industrial use or
equivalent: 110°C (three-phase versions only), 55°C (single-phase
versions).
Tmax 120°C Tmax 120°C
The surfaces of the electric pump may reach high temperatures
based on the temperature of the pumped liquid. Direct contact
and liquid spills may cause burns and injury.
• The direction of rotation of the operating parts is indicated by the marking
(arrow) on the motor support and/or on the fan cover (fig. A9 in appendix).
2.3 Motor energy efficient information
All electric pumps use motors compliant with reg. 640/2009 EC and subsequent
amendments, therefore, compliant with efficiency class IE3 (three-phase versions
with power greater than 0.55 kW). Additional information about motor energy
performance is available online (franklinwater.eu - product data sheet) and on
the motor rating plate.
3 APPLICATIONS AND USE
3.1 Permitted use
These appliances are designed for professional use in applications such as water
supply from groundwater, pressure increase, irrigation or heat transfer fluid
circulation. They can be used in the industrial, manufacturing or equivalent fields.
The electric pumps can also be used in the domestic, commercial, agricultural,
artisan or tertiary sectors, for the same applications, exclusively at a temperature
not exceeding: 90°C for the three-phase versions, 55°C for the single-phase
versions.
NOTE: For other applications, the maximum temperature allowed is 110°C (three-
phase versions only).
Electric pumps must be installed in dry areas and protected from flooding.
The electric pump can work continuously at the maximum room temperature
indicated on the rating plate.
3.2 Pumped liquids
Clean liquids, compatible with the electric pump component materials. A liquid
must have physical characteristics similar to those of clean water at room
temperature (1030 kg/m maximum density and 2 cPs maximum viscosity. If
3
these limits are exceeded, contact the manufacturer).
Improper use can result in overheating of the machine and power cables,
with consequences such as failure and potentially fire.
Any sand content in the water must not exceed 50 g/m3. Higher sand
concentrations will reduce the electric pump service life and increase the risk of
blockage. Any suspended solids must not exceed 0.5 mm in maximum size.
Water intended for human consumption: only models with WRAS certification,
only with cold water.
3.3 Conditions of use
• Maximum operating pressure (pump delivery pressure, obtained by the sum of
the pump inlet pressure and the pressure increase supplied by the pump): see
the rating plate. The maximum pressure at the appliance inlet is determined by
the pressure increase created by the pump, so as not to exceed the maximum
operating pressure (see the section dedicated to the calculation).
• Flow rate and head: during normal operation, they must fall within the fields
indicated on the rating plate. Under these conditions, optimal machine
operation is achieved.
• Sucked liquid maximum temperature: 55°C, 90°C or 110°C depending on use
(see paragraph 3.1).
• Sucked liquid minimum temperature: -10°C (EPDM gaskets); -10°C (Viton®/
FKM gaskets).
10
MONOBLOC VERTICAL MULTISTAGE PUMPS
• Room temperature: maximum 40°C up to 1000 m altitude. If these limits are
exceeded, contact the manufacturer.
• Electrical supply voltage: refer to the motor rating plate. The maximum
deviation allowed is +/- 6% of the nominal value.
• Maximum number of consecutive hourly start-ups: 40.
3.4 Non-permitted use
Do not use the electric pump for applications other than those described
above and, in any case, not authorised by the manufacturer. Improper use may
cause serious damage (including death) to people, animals, objects and the
environment.
Do not use the electric pump connected to swimming pools, basins,
ponds and in similar places when people are in the water.
• Do not pump food liquids or human food products.
• Do not pump any liquids that are more viscous and/or denser than water,
unless specifically authorised by the Manufacturer.
• Do not use the machine in potentially explosive environments or with
flammable liquids.
• Do not run the machine without any liquid.
• To avoid overheating, do not run the electric pump continuously at a flow rate
of zero or lower than 10% of the rated value. If the temperature of the inlet
liquid exceeds 90°C, increase the minimum flow rate to 20% of the nominal
value.
• Do not exceed the maximum pressure indicated on the rating plate.
3.5 Other uses
Contact the Manufacturer if:
• The liquid to be pumped has a viscosity or density higher than that of the water
(it will be necessary to use a motor with a proportionally greater power)
• The water to be pumped is chemically treated (softened, chlorinated, purified,
etc.)
• Any situation other than those listed under permitted use occurs.
4 INSTALLATION – GENERAL
The appliance must be installed in accordance with the instructions in this manual.
The appliance and terminals of the power supply cable must be protected against
water, humidity and atmospheric agents. Check the protection rating (IP)
indicated on the motor rating plate. Install in a location not subject to flooding.
Before starting work on the machine, make sure that it has been
disconnected from the power supply network and that it cannot be
accidentally reconnected.
Always use the required PPE (refer to the relative section).
If required in relation to the conditions of use and the working environment, we
suggest installing adequate devices to immediately perform an emergency stop
of the machine.
4.1 Electrical connections
The connections must be exclusively performed by expert, authorised
personnel and in compliance with legal obligations, current regulations,
consolidated technical practices and the following provisions.
The appliance is designed exclusively for fixed applications (the power cable
cannot be disconnected and reconnected by the user).
Use electric cables of the type and section indicated in table A11 in the appendix.
Tighten the cable gland to the torque indicated in the table (lock it with the collar
inside the terminal box, where present). Always connect the earthing conductor
to the point required inside the terminal box, keeping it longer than the other
conductors. Once wiring is complete, remove the sponge under the terminal
block.
The cable terminals must be connected in an electrical panel with at least an IP55
protection rating, equipped with cable mechanical fixing systems independent
of electrical terminals, and an overvoltage category III omni-polar cut-out switch
preventing the panel from being opened when the appliance is live. The cable
must be protected from excessively high or low temperatures, open flames and
chemical agents.
Make sure the rating plate details match the rated voltage and frequency values.
Always connect the earthing cable to the electric pump and check the earthing
circuit effectiveness before the first start-up and then every month.
Perform the connections as shown in fig. A12, in the appendix.
The installer is responsible for making connections in accordance with the
regulations in force in the country of installation.
The appliance must be powered by a residual current device, with residual
operating current of no more than 30 mA. Check its functionality before
commissioning.