Ryobi RLT430CESB Manual De Utilización página 19

50. Filter screen
51. Air filter cover
Fig.22
52. Spark plug boot
53. Bolt
54. Top housing
Fig.5
55. Drive shaft
KNOW YOUR STRING TRIMMER
See Figure 1.
The safe use of this product requires an understanding of the
information on the tool and in this operator's manual as well as a
knowledge of the project you are attempting. Before use of this
product, familiarise yourself with all operating features and safety
rules.
ERGONOMIC DESIGN
The design of the trimmer provides for easy handling. It is
designed for comfort and ease of grasp when operating in different
positions and at different angles.
GRASS DEFLECTOR
The trimmer includes a grass deflector that helps protect you from
flying debris.
OIL CAP/DIPSTICK
Remove the oil fill cap to check and add lubricant when necessary.
TOP-MOUNTED MOTOR
The top-mounted motor improves balance and is located away
from the dust and debris of the cutting area.
ASSEMBLY
UNPACKING
This product requires assembly.
  C arefully remove the product and any accessories from the
box. Make sure that all items listed in the packing list are
included.
  I nspect the product carefully to make sure no breakage or
damage occurred during shipping.
  D o not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
  I f any parts are damaged or missing, please call Ryobi
customer services for assistance.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories
not recommended for use with this product. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
English(Original instructions)
I N S TA L L I N G T H E P O W E R H E A D S H A F T T O T H E
ATTACHMENT
See Figure 2.
The attachment connects to the power head shaft by means of a
coupler device.
Loosen the Wing Screw on the coupler of the power head
Push in the button located on the attachment shaft. Align the
 Tighten the knob securely.
REMOVING THE ATTACHMENT FROM THE POWER HEAD
For removing or changing the attachment:
 Loosen the knob.
 Push in the button and twist the shafts to remove and separate
ATTACHING THE STORAGE HANGER
See Figure 3.
There are two ways to hang your attachment for storage.
 To use the hanger cap, push in the button and place the hanger
 The secondary hole in the attachment shaft can be used for
ATTACHING THE FRONT HANDLE
See Figure 4.



NOTE: The hex bolt head fits inside the hex recess moulded into
one side of the handle.


17
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
WARNING:
Never install, remove, or adjust any attachment while the
power head is running. Failure to stop the engine can
cause serious personal injury.
shaft and remove the end cap from the attachment.
button with the guide recess on the power head coupler and
slide the two shafts together. Rotate the attachment shaft until
the button locks into the positioning hole.
NOTE: If the button does not release completely in the
positioning hole, the shafts are not locked into place. Slightly
rotate from side to side until the button is locked into place.
WARNING:
Be certain the Wing Screw is fully tightened before
operating equipment; check it periodically for tightness
during use to avoid serious personal injury.
ends.
cap over end of the lower end attachment shaft. Slightly rotate
the cap from side to side until the button locks into place.
hanging purposes as well.
Remove the clamp and bolts from the front handle.
Install the front handle onto the top side of the drive shaft
boom with the barrier bar on the same side as the recoil
starter (compare to product images in figure sheet or on
giftbox)
Place the bolts through the front handle.
Reinstall the clamp.
Tighten bolts securely.