Equipment Installation; Maintenance / Recommendations; Electricity Supply - ims PRO MIG CARPRO 1 Manual Del Usuario

Translation of the original instructions

EQUIPMENT INSTALLATION

• Put the machine on the floor (maximum incline of 10°.)
• Ensure the work area has sufficient ventillation for welding, and that there is easy access to the control panel.
• The machine must be placed in a sheltered area away from rain or direct sunlight.
• The machine must not be used in an area with conductive metal dusts.
• The machine protection level is IP21, which means :
- Protection against acess to dangerous parts from solid bodies of a ≥12.5mm diameter and,
- Protection against vertically falling drops.
• The power cables, extensions and welding cables must be fully uncoiled to prevent overheating.
The manufacturer does not incur any responsability regarding damages to both objects and persons that result from an incorrect
and/or dangerous use of the machine .

MAINTENANCE / RECOMMENDATIONS

• Maintenance should only be carried out by a qualified person. Annual maintenance is recommended.
• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out maintenance work. DANGER
High Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the electrical connections checked by a qualified
person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be replaced by the manufacturer, its after sales
service or an equally qualified person.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
RISK OF INJURY DUE TO MOVING PARTS!
The wire feeders contain moving parts that may catch hand, hair, clothes or tools which can lead to injuries! Take extra care.
• Do not place your hand on mobile/pivoting/wire feeding parts of the machine!
• Make sure that all panels remain closed when in use !
• Do not wear gloves when feeding the wire through or changing reel.
Minimum and maximum filler metal diameter : Ø 0,6 – Ø 0,8 - Ø 1,0 mm
Minimum and maximum wire speed: 1 m/min to 15 m/min
Maximum gas pressure : 0,5 MPa (5 bars).
DESCRIPTION
Thank you for your choosing this product. In order to get the best from your purchase, please read with care the fol-
lowing instructions:
The MIG CARPRO 1 and MIG CARPRO 3 are «synergic» semi-automatic welding units on wheels, ventilated for welding
(MIG or MAG). They are recommended to weld steel, stainless steel, aluminium and for "MIG Brazing" of high-tensile
strength steels with CuSi and CuAl wires (ideal for car body repairs). Their adjustment is quick and easy with their «
synergic wire speed » function. The MIG CARPRO 1 and MIG CARPRO 3 work on 3-phase 400V or on 230V/400V - 3
phase for the MIG CARPRO 3 DV.

ELECTRICITY SUPPLY

The welders are fitted with a 16 A socket type EN 60309-1 which must be connected to a three-phase 400V (50 - 60
Hz) power supply fitted with four wires and one earthed neutral.
The absorbed effective current (I1eff) is displayed on the machine, for optimal use. Check that the power supply and
its protection (fuse and/or circuit breaker) are compatible with the current needed by the machine. In some countries,
it may be necessary to change the plug to allow the use at maximum settings.
MIG CARPRO 3 DV, Power supply 3-phase 230 V :
WARNING: this device is pre-assembled at the factory on 3-phase 400 V. If your electrical installation is on 3-phase
230 V, amend the connections on the terminal block inside the product. This operation must be done by a skilful
person. Please see electrical diagram 230 V located inside the product. The power supply must be protected by a
circuit breaker 16 A and 1 differential 30 mA.
MIG CARPRO 1 / 3 / 3 DV EN
19