Teaching In Without A Remote Transmitter; Teaching In/Deleting A Remote Transmitter; Operation; Programming - Normstahl Magic 1000-2 Manual Del Usuario

Once the door operator has been taught
in, key A is used for remote control and
the other keys can be used to control
other similar door operators or other
radio receivers.
Teaching in
• Press and hold down key A; the door
moves in the open direction.
• When you reach the desired end position "OPEN", release
key A. (You can make corrections with key B.)
• Press key C once briefly, teach-in procedure: The door
operator automatically stores "End position OPEN/CLOSE"
and the loads of the "Travel path OPEN/CLOSE". The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.

Teaching in without a remote transmitter

On the door operator:
• Press and hold pushbutton
open direction. Release pushbutton when the desired
opening position is reached. A correction can be made with
the pushbutton .
• Press the Menu pushbutton
automatically stores "End position OPEN/CLOSE" and the
loads of the "Travel path OPEN/CLOSE" . The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.
16 Teaching in/deleting a remote
transmitter
Programming the remote transmitter:
During one of the 3 status messages A, B or C (see Chapter
10), press the pushbuttons
(approx. 1 s), F0 flashes in the display.
Select the desired function with the pushbuttons
Functions
F0 OPEN / Stop / CLOSE
F1 OPEN / Stop / OPEN
F2 CLOSE / Stop / CLOSE
F3 Stop
F4 Partial opening
F5 Light ON (restart light time)
F6 Light ON / OFF
F7 OPEN
F8 CLOSED
Press the desired key on the remote transmitter, the radio
command is taught in.
Note: The number of the function is shown in the display
during the transmission pulse.
Programming a new remote transmitter (TX) using an
existing one
Perform the following steps:
1 Go near door
2+3 programmed TX, within 3 seconds
Magic 1000-2
and the door moves in the
, the door operator
and simultaneously
and
4 new TX, within 10 seconds
5 wait 10 s
Deleting (all) remote transmitter(s):
During one of the 3 status messages A, B or C (see Chapter
10), press the pushbuttons
seconds, FL flashes in the display. The status message
reappears after 3 seconds.

17 Operation

CAUTION: Mishandling the product can result in
injuries or material damage. Follow the basic safety
rules:
When opening or closing the door, do not block the interior or
exterior swivel ranges. Keep children away.
The door movements can be activated or stopped using the
remote transmitter provided or via switching elements such
as the wall keypad, which can be connected if desired.
Optional external features (such as the EMERGENCY
STOP) can also be connected to the door operator.
The operator must be connected to a door before
it is used. If it is not, incorrect load values will be
taught in to the electronic system. This can cause
malfunctions.

18 Programming

.
Switch on programming mode
During one of the 3 status messages A, B or C (see Chapter
10) press the Menu pusbutton
seconds. The display changes to the menu (D).
Select programming menu
Select the desired menu with the pushbuttons
Show / change menu value
Displays: Press the Menu pushbutton
seconds, the menu value (E) is displayed.
Change: Change the value with the pushbuttons
Save: Press the Menu pushbutton
seconds, the programming menu (D) is displayed.
Exit programming mode
Press the Menu pushbutton
the display changes to the status message, changes are
saved.
IP2286 12/2017
and simultaneously for >6
for longer than 1.5
and .
for less than 1.5
and
for less than 1.5
for longer than 1.5 seconds,
15 / 219
.