Troubleshooting - Pit Boss PLATINUM BRUNSWICK PBV5PL Instrucciones Y Recetas

Ahumador vertical de pellas de madera
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Proper cleaning, maintenance and the use of clean, dry, quality fuel will prevent common operational problems. When your Pit
Boss® grill is operating poorly, or on a less frequent basis, the following troubleshooting tips may be helpful. For FAQ, please visit
www.pitboss-grills.com . You may also contact your local Pit Boss® authorized dealer or contact Customer Care for assistance.
WARNING: Always disconnect the electrical cord prior to opening the grill for any inspection, cleaning,
maintenance or service work. Ensure the grill is completely cooled to avoid injury.
PROBLEM
CAUSE
No Power Lights On
Not Connected To Power
The Control Panel
Source
Fuse Blown On The
Control Panel
The GFCI outlet has
been tripped.
Faulty Control Panel
Fire in Burn pot Will
Auger Not Primed
Not Light
Auger Motor Is Jammed
Ignitor Failure
Readout of actual
Grill probe dirty
temperature will not
Grill probe is broken
adjust
Grill Will Not Achieve
Insufficient Air Flow
Or Maintain Stable
Through Burn pot
Temperature
Lack Of Fuel, Poor Fuel
Quality, Obstruction In
Feed System
Grill Probe
Grill Produces Excess
Grease Build-Up
Or Discolored
Wood Pellet Quality
Smoke
Burn pot Is Blocked
Insufficient Air Intake
For Fan

TROUBLESHOOTING

SOLUTION
Ensure unit is plugged into a working power source. Reset breaker. Ensure GFCI is a minimum 10 Amp
service (see Electric Wire Diagram for access to electric components) Ensure all wire connections are
firmly connected and dry.
Remove hopper access panel (see Electric Wire Diagram for diagram), press in plastic tabs holding
the Control Panel in place and carefully pull controller inside the hopper to release controller. Check the
fuse for a broken wire or if the wire has turned black. If yes, fuse needs to be manually replaced.
Remove hopper access panel (see Electric Wire Diagram for diagram), and ensure all wire connections
are firmly connected and dry. Ensure GFCI is a minimum 10 Amp service.
Control Panel needs to be replaced. Contact Customer Care for a replacement part.
Before the unit is used for the first time or anytime the hopper is completely emptied out, the auger
must be primed to allow pellets to fill the auger tube. If not primed, the ignitor will timeout before
the pellets reach the burn pot. Follow Hopper Priming Procedure .
Remove cooking components from the main barrel. Press the Power Button to turn the unit on and
inspect the auger feed system. Visually confirm that the auger is dropping pellets into the burn pot. If
not operating properly, call Customer Care for assistance or a replacement part.
Remove cooking components from the main barrel. Press the Power Button to turn the unit on and
inspect the ignitor. Visually confirm that the ignitor is working by placing your hand above the burn
pot and feeling for heat. Visually confirm that the ignitor is protruding approximately 13mm / 0.5
inches in the burn pot. If not operating properly, call Customer Care for assistance or a replacement part.
Follow care and maintenance instructions.
Grill probe needs to be replaced. Contact Customer Care.
Check burn pot for ash build-up or obstructions. Follow Care and Maintenance instructions for
ash build-up. Check fan. Ensure it is working properly and air intake is not blocked. Follow Care and
Maintenance instructions if dirty. Check auger motor to confirm operation, and ensure there is no
blockage in the auger tube. Once all the above steps have been done, start the grill, set temperature
to SMOKE and wait for 10 minutes. Check that the flame produced is bright and vibrant.
Check hopper to check that fuel level is sufficient, and replenish if low. Should the quality of wood
pellets be poor, or the length of the pellets too long, this may cause an obstruction in the feed system.
Remove pellets and follow Care and Maintenance instructions.
Check status of grill probe. Follow Care and Maintenance instructions if dirty. Contact Customer Care
for a replacement part if damaged.
Follow Care and Maintenance instructions.
Remove moist wood pellets from hopper. Follow Care and Maintenance instructions to clean out.
Replace with dry wood pellets.
Clear burn pot for moist wood pellets. Follow Hopper Priming Procedure.
Check fan. Ensure it is working properly and air intake is not blocked. Follow Care and Maintenance
instructions if dirty.
23

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

1057710932Pbver5000pl10577

Tabla de contenido