Storage; Returning The Product; Product Description; Proper Use And Fields Of Application - salmson Rocsan lix Instalacion Y Puesta En Servicio

English
3.3.

Storage

Newly supplied products are prepared so that they can be stored
for at least 1 year. The product should be cleaned thoroughly
before it is put into temporary storage.
The following should be taken into consideration for storage:
• Place the product on a firm surface and secure it against
slipping and falling over. Wastewater submersible pumps
are stored vertically.
DAnGER from falling over!
never set down the product unsecured. If the
product falls over, injury can occur!
• Our products can be stored at temperatures down to
-15 °C. The store room must be dry. We recommend a
frost-protected room for storage with a temperature
between 5 °C and 25 °C.
• The product may not be stored in rooms where welding
work is conducted as the resulting gases and radiated heat
can damage the elastomer parts and coatings.
• Any suction or discharge ports should be closed tightly
before storage to prevent impurities.
• The current supply cables should be protected against
kinking, damage, and moisture.
ELECTRICAL hazard!
Damaged power supply cables can cause fatal inju-
ry! Defective cables must be replaced by a qualified
electrician immediately.
BEWARE of moisture!
Moisture penetrating the cable will damage both
the product and the cable. never immerse the
cable end in fluid and always protect it from mois-
ture.
• The product must be protected from direct sunlight, heat,
dust, and frost. Heat and frost can cause considerable
damage to rotors and coatings!
• The impellers must be turned at regular intervals. This pre-
vents the bearings from jamming and the film of lubricant
on the mechanical shaft seal is renewed.
BEWARE of sharp edges!
Sharp edges can form on impellers and hydraulic
ports. there is a risk of injuries! Wear the necessary
protective clothing, e.g. safety gloves.
• If the product has been stored for a long period of time
it should be cleaned of impurities such as dust and oil
deposits before start-up. Rotors should be checked
for smooth operation. The housing coatings should be
checked for damage.
Before start-up, the filling level in the oil separa-
tion chamber should be checked and topped up, if
necessary.
Damaged coatings should be repaired immediately.
only a coating that is completely intact fulfills the
criteria for intended use.
All manuals and user guides at all-guides.com
If these rules are observed, your product can be stored for a
lengthy period. Please remember that elastomer parts and coat-
ings become brittle over time. If the product is to be stored for
longer than 6 months, we recommend checking these parts and
replacing them as necessary. Consult the manufacturer for details.
3.4.
Products that are returned to the factory must be properly
packaged. This means that impurities have been removed from
the product and that it has been decontaminated if used with
fluids that are hazardous to health. The packaging must protect
the product from damage during transportation. If you have any
questions please contact the manufacturer.
4.
The product has been manufactured with great care and is subject
to constant quality controls. Trouble-free operation is guaranteed
if it is installed and maintained correctly.
4.1.
The Salmson-Rocsan lix... submersible motor pumps are suitable
for intermittent operation, pumping the following fluids:
when draining buildings and properties in accordance with
EN 12050 (while observing country-specific forewords and
regulations such as DIN EN 12050-1) and when used in pits and
reservoirs.
The submersible motor pumps must not be used for pumping:
Proper use also includes observation of this manual. Any other use
is regarded as improper.
4.2.
The Salmson-Rocsan units... are flood-able submersible waste
water motor pumps, which can be operated vertically as both
stationary and portable wet installations.
36

Returning the product

Product description

Proper use and fields of application

• Sewage and waste water
• Waste water containing feces
• Sludge up to a maximum of 8 % dry solids (depending on
the type)
• Drinking water
• Fluids with hard components such as stone, wood, metal
and sand.
ELECTRICAL hazard
When using the product in swimming pools or oth-
er accessible pools, there is a risk of electrocution.
note the following information:
• Use is strictly forbidden if there are people in the
pool!
• If there are no people in the pool, protective mea-
sures must be taken according to DIN VDE 0100-
702.46
(or the appropriate national regulations).
The product is intended for pumping waste water.
Therefore, pumping drinking water is strictly pro-
hibited!

Construction