Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
1.3 OPERATING HAZARDS
•
Use of the tool can expose the operator's hands to hazards, including crushing, impacts, cuts, abrasions and heat. Wear
suitable gloves to protect hands.
•
Operators and maintenance personnel shall be physically able to handle the bulk, weight and power of the tool.
•
Hold the tool correctly; be ready to counteract normal or sudden movements and have both hands available.
•
Keep tool handles dry, clean and free from oil and grease.
•
Maintain a balanced body position and secure footing when operating the tool.
•
Release the start-and-stop device in the case of an interruption of the air supply.
•
Use only lubricants recommended by the manufacturer.
•
Contact with hydraulic fl uid should be avoided. To minimize the possibility of rashes, care should be taken to wash
thoroughly if contact occurs.
•
Material Safety Data Sheets for all hydraulic oils and lubricants is available on request from your tool supplier.
•
Avoid unsuitable postures, as it is likely for these positions not to allow counteracting of normal or unexpected
movement of the tool.
•
If the tool is fi xed to a suspension device, make sure that the fi xation is secure.
•
Beware of the risk of crushing or pinching if nose equipment is not fi tted.
•
DO NOT operate tool with the nose casing removed.
•
Adequate clearance is required for the tool operator's hands before proceeding.
•
When carrying the tool from place to place keep hands away from the trigger to avoid inadvertent activation.
•
DO NOT abuse the tool by dropping or using it as a hammer.
1.4 REPETITIVE MOTIONS HAZARDS
•
When using the tool, the operator can experience discomfort in the hands, arms, shoulders, neck or other parts of the
body.
•
While using the tool, the operator should adopt a comfortable posture whilst maintaining a secure footing and
avoiding awkward or off -balance postures. The operator should change posture during extended tasks; this can help
avoid discomfort and fatigue.
•
If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing, aching, tingling,
numbness, burning sensations or stiff ness, these warning signs should not be ignored. The operator should tell the
employer and consult a qualifi ed health professional.
1.5 ACCESSORY HAZARDS
*
Disconnect the tool from the air supply before fi tting or removing the nose assembly or accessory.
*
Use only sizes and types of accessories and consumables that are recommended by the manufacturer of the tool; do not use
other types or sizes of accessories or consumables.
1.6 WORKPLACE HAZARDS
*
Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by use of the tool and of trip
hazards caused by the air line or hydraulic hose.
*
Proceed with care in unfamiliar surroundings. There can be hidden hazards, such as electricity or other utility lines.
*
The tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electric power.
*
Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by use of the tool.
*
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
1.7 NOISE HAZARDS
•
Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus
(ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment and the implementation of appropriate
controls for these hazards are essential.
•
Appropriate controls to reduce the risk may include actions such as damping materials to prevent work pieces from
"ringing".
•
Use hearing protection in accordance with employer's instructions and as required by occupational health and safety
regulations.
•
Select, maintain and replace the consumable/inserted tool as recommended in the instruction handbook, to prevent an
unnecessary increase in noise.
1.8
VIBRATION HAZARDS
•
Exposure to vibration can cause disabling damage to the nerves and blood supply of the hands and arms.
•
Wear warm clothing when working in cold conditions and keep your hands warm and dry.
If you experience numbness, tingling, pain or whitening of the skin in your fi ngers or hands, stop using the tool, tell
your employer and consult a physician.
4
O R I G I N A L I N S T R U C T I O N
Publicidad
