Dual CS 607 Manual De Instrucciones página 11

Interference may be caused by:
1. External vibrations. They occur when the turntable is placed
on a table or shelf in a room with wooden floor. External
vibrations, such as footsteps are transferred from the floor
to the furniture and from there to the turntable. Solution:
rotate the dial rings of the acoustic isolators clockwise (+).
amount.
This will provide optimum acoustic isolation.
Cartridge and stylus
Please refer to the enclosed data sheet supplied separately with
your unit.
Replacing the cartridge (Dual TKS .. . )
You may release the complete cartridge from the tonearm by
pressing the tonearm lift 10 to the rear. When doing this, firmly
grip the cartridge as it will fall off once the locking device has
been released (Fig. 7).
In order to replace the cartridge (Dual TKS .. . ) you must
place it from below against the headshell so that the front edges
are flush. Please ensure that the cartridge lies absolutely flat on
the headshell before pulling the tonearm lift to the front in order
to lock it in position (Fig. 8). You may then, if desired, reinsert
the safety screw 11
Stylus
The stylus is subject to natural wear and tear during normal
playing. Therefore, we recommend you occasionally check the
stylus and, in the case of diamond styli, this should be carried
out after approximately
300
playing hours. Your specialist
dealer will be pleased to do this for you free of charge. Worn
or damaged (splintered) styli chisel the modulation from the
grooves and destroy records. Therefore, only use as replacements
the stylus types recornmended
in the technical data of the
cartridge. Imitated styli result in audible quality losses and in-
creased wear and tear of records. Please remember that, for
physical reasons, the stylus holder with the diamond stylus is
extremely fine and must therefore be necessarily sensitive to
impacts, shocks or uncontrolled movement.
Fitting a cartridge
In the case of units delivered without a cartridge, or if you wish
to fit a cartridge of your own choice.
All cartridges having a total weight of 4.5 — 10 g (including the
attachment fittings) may be fitted. Units without a cartridge
are supplied with the necessary fitting accessories (also available
as special accessories under the Dual part No. 269 611 — in the
case of turntables with tuning anti-resonator — Dual part No.
266 048)
The 1/2" cartridge is fitted as follows
1) If necessary, remove the safety screw (Fig. 8/11)
2) Remove the cartridge from the headshell as described in
the section "Replacing the cartridge"
Red R right channel
Green RG right channel ground
Blue GL left channel ground
White L left channel
When fitting the retaining plate with the cartridge fitted,
ensure that the front edge of the black plastic section is
flush with the headshell. The metallic-coloured mounting
plate projects approx. 5 mm.
must fit the additional weight included as an accessory. For
this purpose, screw the countersunk screw completely into
the additional weight and then screw this into the rear of the
tonearm counterweight.
In the case of turntables fitted with a tuning antiresonator,
screw 1 or 2—dependingon the total weight of the cartridge —
of the disc-shaped additional weights included as accesories
onto the rear of the tonearm counterweight 1 .
5;
Cartridge - Total weight - Including hardware
upto 6g 1 thin disc
upto 7g 1 thick disc
upto 9g 1 thick disc and 1 thin disc
up to 10g 2 thick discs
Screw the smaller thread of the special screw into the coun-
terweight 1. With the bevelled side to the outside, screw
the corresponding additional weights onto the thicker part
of the screw.
7
Servicing
The platter
The platter lies directly on the motor spindle and, when placed
in position, is automatically fixed through its own weight. Aa
ditional locking is not necessary and is also not provided for.
Important! Remove the platter before transporting the unit!
Subsequent transport
Ensure that the tonearm is locked and the stylus cover is in position.
Electrical safety
11