Publicidad
Idiomas disponibles
Idiomas disponibles
Releasing "
" button SB1, the machine will stop immediately.
DESCENT
- Press "
" button SB2, the safety pawl will be lifted by joint gas
loop and lowering- -electromagnetic valve opens because of electricity.
The platform is lowering, release button "
safety pawl falls on the safety gear.
PLATFORMS MISALIGNED
In case of platforms misaligned, either due to machine failure or
non-uniform weights, there is a safety photocell for extreme
unevenness, stopping working immediately. If you need to move the
platforms, press the red button plus the desired up or down button.
ELECTRONIC BOARD LEDS
1.- Pushbutton Up
2.- Pushbutton Down
3.- Pushbutton Photocell Off / Bleed
4.- Pushbutton Look
5.- Up Limit Switch
6.- Safety Foot Limit Switch
7.- Not Used
8.- Safety Photocell
EMERGENCY LOWERING
In the event of a power cut, the electrovalves that control the lowering
operation, Y1, Y2 and Y3, cannot be opened. As a result, the
platforms cannot be lowered. In such cases, the platforms can be
brought down to their bottom position by opening the manual
operation screws so that the vehicle can be lowered and removed
from the lift.
Y3 – Y1 – Y1 – Y2
MAIN LIFT
Push the button in the valves Y1
at the same time, hold pushing
and unscrew the valve Y3
NOT IN-PHASE STOP MACHINE
When two platforms are not at the same height during lifting and
lowering operations, photo-electricity leveling equipment will stop
working immediately. According to the following process to adjust the
platform level, only after two platforms are at the same height can put
them into use.
004152 – 04/2021
", stop lowering, the
AUXILIARY LIFT
Push the button in the valve Y2,
hold pushing and unscrew the
valve Y3
Oil make-up "adjust" operation (normal service period) after
completion of machine installation and adjustment in the
application process, the right platform is lower than the left one
(looking from machine head) because of normal looses or
leakage of the hydraulic oil.
When conducting oil make-up operation, the platforms must not
be load.
MAINTENANCE AND CARE
THIS LIFT IS CONSIDERED A RISK EQUIPMENT
ACCORDING TO ANNEX IV OF DIRECTIVE 2006/42/EC
, THEREFORE IS COMANDATORY TO REVIEW IT
ACCORDING TO THE MANUFACTURER'S
INSTRUCTIONS BY PERSONNEL COMPETENT AND
SPECIALIZED
DAILY MAINTENANCE
Check the level of the tank and fill
it if it is necessary up to 1cm below
the filling cap
WEEKLY MAINTENANCE
Lubricate the sliding blocks and
keep the surface clean
Lubricate the bearings
MANUFACTURER MAINTENANCE
Clean the filter of the tank every 6
months
Disassemble the sliding blocks and
the lateral plates and lubricate
Change the oil every 12 months
Perform maintenance operation
described in the Review Check List
(ref.001359) marked by Velyen
every 12 months
TRANSPORT
Packing can be lifted or moved by lift trucks, cranes or bridge
cranes.
In case of slinging, a second person must always take care of the
load, in order to avoid dangerous oscillations.
At the arrival of the goods, check for possible damage due to
transport operations. Also verify that all items specified in the delivery
notes are included. In case of missing parts, possible defects or
damage due to transport operations. Also verify that all items specified
in the delivery notes are included. In case of missing parts, possible
defects or damage due to transport, the person in charge or the carrier
must be immediately informed.
Furthermore, during loading and unloading operation goods
must be handle as shown in the picture.
STORAGE
-The machine equipment should be stocked in the warehouse, if
stocked outside should do the disposal well of waterproof.
Personnel competent
Own
and specialized
✓
✓
Personnel competent
Own
and specialized
✓
✓
✓
✓
Personnel competent
Own
and specialized
✓
✓
✓
✓
✓
✓
✓
NO
Pág. 20
Publicidad
