Gardena SmallCut 300 Libro De Instrucciones página 8

b) Use only the manufacturer's recommended replacement parts and
accessories.
c) Inspect and maintain the machine regu larly. Have the machine repaired only
by an authorized repairer.
d) When not in use, store the machine out of reach of children.
Recommendation
The machine should be supplied via a resid ual current device (RCD) with a trip-
ping current of not more than 30 mA.
Additional Safety Recommendations
DANGER! Risk of suffocation! Small parts can be easily swallowed. There is also
a risk that the polybag can suffocate toddlers. Keep toddlers away when you
assemble the product.
DANGER! When wearing hearing protection, and due to the noise produced by
the product, the operator may not notice persons approaching.
If the product starts unintentionally when the mains plug is connected, disconnect
the mains at once. Contact GARDENA Service to check the product.
DANGER! Risk of cardiac arrest! This product generates an electromagnetic field
while it operates. This electromagnetic field may affect the functionality of active
or passive medical implants (e. g. pacemakers), which may result in serious injury
or death. Consult your doctor and the manufacturer of your implant before using
this product. After using the product, disconnect the mains plug from the mains
socket.
Cables
Use only permitted extension cables as per HD 516.
v Ask your electrical specialist.
If the product got hot during operation, let it cool down before storage.
2. ASSEMBLY
DANGER!
Risk of injury!
Cut injury when the product starts accidentally.
v Before you assemble the product, make sure that the mains
cable is disconnected.
To assemble the trimmer [ Fig. A1 / A2 ]:
1. Put the top part of the handle
they make a click (click). Ensure that the two arrows
other. The cable must not be stretched or caught when you do this.
3
2. Put the bottom handle
a click (click). Ensure that the two arrows
3. Put the cover 4 on the trimmer head
5
feed the cutting filament
4. Put the cover 4 on the trimmer head
Make sure that all cams lock in position.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Before you connect, adjust or transport the product,
disconnect the mains cable and transport the product by
the bottom handle.
To connect the trimmer [ Fig. O1 ]:
DANGER!
Electric shock!
To avoid damage to the mains cable
cable 6 must be inserted into the cable lock
v Before you operate the product insert the extension cable
into the cable lock 7 .
1. Loop the extension cable
pull tight.
2. Connect the plug 8 of the product into the socket
6
cable .
3. Connect the extension cable
Work position [ Fig. O2 ]:
v Hold the product by the top part of the handle
handle 3 so that the trimmer head
Make sure, the filament does not touch hard objects such as walls, stones
and fences to prevent the filament from welding together or breaking.
8
GAR_9805-20.960.08_2023-11-03.indd 8 GAR_9805-20.960.08_2023-11-03.indd 8
1 2
and the trimmer head together until
> face each
1
on the top part of the handle until it makes
B face each other.
2 while you
4
through the opening in the cover
2 until it makes a click (click).
8 the extension
7 .
6
, insert the loop into the cable lock
9 of the extension
6
into a 230 V mains socket.
1 and the bottom
2 is tilted a small distance forward.
To start the trimmer [ Fig. O3 ]:
DANGER!
Risk of injury if the product does not stop when you
release the start button.
v Do not bypass the safety devices or switches. For example do
not attach the start button
To start:
v Push the start button
To stop:
v Release the start button
To extend the cutting filament (Tip mechanism) [ Fig. O4 / O5 ]:
The tip mechanism operates when the motor operates. The best
result occurs only with the maximum cutting filament length. During first
operation, it can be necessary to extend the cutting filament many times.
1. Start the product.
2. Hold the trimmer head
2
trimmer head onto a solid surface (prevent constant pressure for
extended periods).
The cutting filament 5
that can be heard and adjusted to the correct length with the filament
q
limiter . If necessary tap many times again and again.
4. MAINTENANCE
DANGER!
Cut injury when the product starts accidentally.
v Before you maintain the product, make sure that the mains
cable is disconnected.
To clean the trimmer [ Fig. M1 ]:
DANGER!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
.
The airflow slots must always be clean.
1. Clean the airflow slots
2. Clean all movable parts after each operation. Especially remove any
grass and dirt from the cover
To replace the filament cassette [ Fig. M2/M3 ]:
DANGER!
Risk of injury from metal cutting parts!
v Do not use metal cutting parts or replacement parts and
accessories not approved by GARDENA.
Only use original GARDENA Filament Cassettes. You can order
Replacement Filament Cassettes from your GARDENA dealer or
directly from the GARDENA Customer Service.
For Art. 9805 SmallCut 300 / Art. 9806 SmallCut Plus 350:
GARDENA Filament Cassette for Turbotrimmers Art. 5307.
1. Push in cassette cover
and remove.
6
2. Remove the filament cassette
3. Remove all dirt.
7
and
4. Pull approximately 15 cm of the cutting filament
filament cassette t
5. First put the cutting filament
6. Put the cutting filament
7. Put the filament cassette
8. Attach the cassette cover
you hear both locking clips
When attaching the cassette cover
put around the guide pin
Risk of injury!
0 to the handle.
0 1
on the top part of the handle .
0 .
2 parallel to the ground and briefly tap the
is automatically extended with a mechanism
Risk of injury!
Electric shock!
w
with a soft brush (do not use a screwdriver).
4 .
Risk of injury!
e r
on the two locking clips at the same time
t .
5 out of the new
through the hole in the plastic ring z
5
through the metal sleeve
5 around the guide pin i .
t
into the filament cassette holder
e
on the filament cassette holder
r make a click.
e , the cutting filament
i and must not be caught.
.
u
.
o
.
o
until
5 must be
03.11.23 09:53 03.11.23 09:53