Publicidad
Idiomas disponibles
Idiomas disponibles
COMMISSIONING AND USE
INITIAL LOAD
The INITIAL LOAD menu allows for pre-loading pellets for 90 seconds,
when the appliance has been switched off and has cooled down.
This function may be useful if the appliance is switched on after the
tank has been completely emptied, or when it is filled for the first time.
The function starts by pressing the
the
button.
O
a
WARNING: once the operation has been completed,
before switching on the appliance you should re-
move any pellets accumulated inside the brazier.
STOVE STATUS
The STOVE STATUS menu allows for instantly viewing the status of
the appliance, by showing the operating conditions of the various de-
vices connected to it. Several pages are displayed in succession.
The table below shows the possible statuses of the devices and their
meaning.
Status
Meaning
L04-270218
Code of the firmware loaded in the control unit.
(example)
Indicates the temperature measured by the
T.PELLET
sensor in the pellet-side smoke chamber.
Indicates the room temperature measured by the
T.ROOM
probe on the remote control.
T.ROOM 1
Not used
T.ROOM 2
Not used
ASP.RPM
Indicates the speed of the fume extractor.
LOAD
Indicates the pellet loading interval.
Indicates the status of the main room thermostat
(OFF = Room thermostat contact OPEN =
STATUS T.A.
Thermostat not triggered; ON = Room thermostat
contact CLOSED = Thermostat triggered)
AIR SPEED
Not used
DUCHT.
Indicates the speed of the air fan on the pellet
PELLET
side.
Indicates the speed of the air fan on the wood
DUCHT.WOOD
side.
Indicates the end (in minutes) of the current
TIMER 1
operating phase.
Indicates the end (in seconds) of the current
TIMER 2
operating phase.
In the event of an alarm, it indicates the time (in
ALARM DELAY
seconds) after which the alarm appears on the
display.
T.MOTHER-
Indicates the temperature measured by the
BOARD
sensor inside the control unit.
Indicates the hours remaining before requesting
a service for the pellet side, from the Technical
SERVICE P
Assistance Centre.
At the expiry of the hours, "SERVICE EXPIRY" will
appear on the display.
Indicates the status of the level sensor for pellets
in the tank (OFF = Sensor covered = Pellets in
PELLET LEV.
the tank above the reserve limit; ON = Sensor
(*)
exposed = Pellets in the tank below the reserve
limit)
CS.DLA.IST_EN_Rev. 1.0_11-23
button and stops by pressing
+
Status
Meaning
Indicates the status of the brazier cleaner (OFF
G.A.S.
= Contact OPEN = Brazier not aligned; ON =
Contact CLOSED = Brazier aligned)
Indicates the radio channel that the remote
RADIO ID
control is linked to.
Indicates the temperature measured by the
T.WOOD
sensor inside the air cavity on the wood side.
Indicates the hours remaining before requesting
a service for the wood side, from the Technical
SERVICE W
Assistance Centre.
At the expiry of the hours, "SERVICE EXPIRY" will
appear on the display.
(*) If present.
WI-FI STATUS
By selecting the RESET/WPS field within the WI-FI STATUS menu, it is
possible to link the Wi-Fi module to the Internet network via WPS or dis-
connect it from the Internet network to which it was previously connected.
TECHNICAL SETTINGS
a
WARNING: menu reserved for the Technical Assis-
tance Centre. Access by unauthorised personnel
can cause serious damage to the appliance, objects
and the environment, as well as personal injuries.
The manufacturer declines all responsibility deriving
from improper calibration of these values.
USER SETTINGS
a
WARNING: menu dedicated to expert users only. Ac-
cess by inexpert users can cause serious damage to
the appliance, objects and the environment, as well
as personal injuries. The manufacturer declines all
responsibility deriving from improper calibration of
these values.
The USER SETTINGS menu allows the user to make a limited calibra-
tion of the pellet load (TYPE PELLET) and of the flue gas extractor
speed (TYPE CHIMNEY) according to the procedures indicated in the
following table.
Menu
Meaning
By increasing the value by a single
unit, the pellet load is increased
by about 2%.
TYPE PELLET
By reducing the value by a single
unit, the pellet load is reduced by
about 2%.
By increasing the value by a
single unit, the flue gas extractor
speed (and therefore the flow of
combustion air) is increased by
about 3%.
TYPE CHIMNEY
By reducing the value by a
single unit, the flue gas extractor
speed (and therefore the flow of
combustion air) is reduced by
about 3%.
EN
Settable
values
-4÷+4
-4÷+4
25
Publicidad
