Sunrise Medical BREEZY RELAX Manual De Usario página 18

Options - Wheelbase extension
Wheelbase extension (7.56)
The larger the wheelbase, the less
likely the wheelchair is to tip over.
The rear wheel is fitted in the most
rear position to extend the wheel-
base. Make sure that after any
adjustment work, all screws are
tightened correctly (see the page
on torque).
CAUTION!
Wheel locks must be adjusted to suit the new
position!
With built-in frame extension, the
stability of the wheelchair and the
drive characteristics can be impro-
ved. By loosening the screws (1)
the frame can be lengthened .
Make sure that after any adjust-
ment work, all screws are tighte-
ned correctly (see the page on tor-
que).
CAUTION!
The chassis frame must not be
pulled out longer than the seat
frame.
Options - Backrest height
7.77)
Comfort backrest (
The Comfort backrest will allow
you to sit for long periods of time,
with side support. To remove it,
pull it upwards and forwards. The
cushion is held by Velcro and can
also be removed. The cover can be
washed (see the instructions on
the cushion).
Adjustable backrest height (7.77.4)
The backrest height can be adjusted to various posi-
tions by releasing the 4 clamp screws (1). Then tigh-
ten the clamp screws again (see the page on torque).
7.77.5)
Side pads (
The angle, depth and height of the
side pads can be adjusted and
they can also be swung-away or
removed.
• Depth adjustment: Loosen the
screw (1) and put the pad into its
new position. Tighten the screw.
• Angle adjustment: Push the pad
upwards, put the pad at the desired angle and then
let go of it again. It will automatically click into pla-
ce. This is how you swing the pad away.
• Height adjustment: Loosen the
screw (2) and put the bracket
into the desired position. If there
is not sufficient adjustment, the
pad can also be fitted into a new
position on the bracket. Then
tighten the screws.
18
Breezy Relax/Quickie Relax
Adjustable back angle
(8°-40°/50°) (7.79)
By pulling the lever (1) the backrest
is released and can be put into the
desired position.
When you let go, the backrest is
automatically fixed in the new
position.
CAUTION:
The angle-adjustable backrest may only be used
with anti-tip tubes. The gap between the anti-tip
tubes and the ground must be a maximum of 2,5
cm.
CAUTION:
To ensure the correct function of the cables, the-
se must never be taut.
CAUTION:
There is a risk of injury when you adjusting the
1
backrest.
CAUTION:
Never adjust the backrest if the wheelchair is on
a slope.
Options - Height-adjustable sideguard
Height-adjustable sideguard
(7.81.1)
The armrest can be height-adju-
sted or removed as follows. Push
the knob (1) and adjust the armrest
(2) to the desired height. Always
check that the armrests are correc-
tly engaged.
You can set the armrest depth after
releasing the hand wheel (3). After-
wards, tighten the hand wheel.
CAUTION!
Neither the sideguards nor the armrests are to
be used for lifting or carrying the wheelchair.
Options - Hemi
Hemi armrest
The hemi armrest can be adjusted
both in length and angle. You can
adjust the length by pushing the
armrest after having loosened the
2 rotary screws (1). To adjust the
angle, hold the knob 2 pushed
down and then turn the armrest to the desired
height and then release the knob.
A
1
1
3
2
1
0305/3/ST-000690xxx.EMS