Cloer -5928 Instrucciones De Uso página 9

Technical Data
type volt
592 220-240
Before the first use
Read these operating instructions
carefully before using the appliance
for the first time.
• Remove all packaging elements and labels, but
• not the rating plate.
• Place the espresso maker on a dry, level, and non-slip
surface.
• Make sure that the power cord never comes into con-
tact with hot surfaces.
• Do not stretch the cord over corners and edges.
EC Label / Safety information
The appliance meets the requirements
of the applicable EC directives.
The appliance is designed
for indoor domestic use only.
ATTENTION! Always unplug the appliance
when not in use and before cleaning.
Move the pin in the middle of the safety
valve before each use, especially after
long periods of non use, with a finger a
few times back and forth. This ensures
that the valve works properly.
• Clean the coffee pot, the filter insert, and the water
tank under clear, warm water to remove any possible
production residue.
• Make sure not to immerse the contact base or
• the water tank in water.
• For hygienic reasons, we recommend that you prepare
and pour away a cup of espresso before making your
first real cup of espresso. You can brew this trial espres-
so with the amount of coffee required to make 3 cups.
• Use the espresso maker only with the provided con-
tact base.
• Do not place the contact base and the coffee pot on
a stove or gas flame.
• The contact base may only be operated when it is dry.
• Please make sure that water is never spilled on the
contact base.
• If water is accidentally spilled onto the contact
• base, proceed as follows:
– Unplug the unit from the wall socket.
– Dry the contact base with an absorbent dry kit-
chen towel.
– Dry the surface beneath the contact base.
– Plug the unit into the wall socket again.
hz watt
50 330-400
• Do not open the lid of the coffee pot during opera-
• Wait until the boiling process is complete and the
• Coution! Do not remove the espresso maker from
• Unplug the power cord immediately if the appliance, the
• Unplug the appliance after using it.
• Use only espresso coffee powder.
• Fill the water tank with water up to the "6" mark.
• Take the 6 cup filter insert (including the coil) and fill
• Smoothen the espresso powder across the brim, but
• Insert the filled filter insert into the water tank.
• Remove any leftover powder from the brim to allow
• Screw the top of the espresso maker to the water tank.
• Place the top of the espresso maker straight onto the
• The arrows on the top of the espresso maker and wa-
• Make sure the tanks do not tilt and the pot is closed
• You can now place the espresso pot onto the con-
• Insert the plug into the wall socket.
• Switch the espresso maker on.
• Do not open the lid during operation. Danger of scalding!
• The espresso is finished as soon as the control lamp
• Unplug appliance from the wall socket.
• You can now serve the espresso.
• Before making more espresso, let the appliance
• After that please clean the espresso maker according
• Then, proceed as described above.
CAUTION! The espresso maker
becomes hot during operation.
There is a hazard of burn injury!
Avoid touching the surface of the
appliance. Grab the espresso maker
only by its insulated handle!
tion. Scalding may result from escaping steam!
control lamp turns off.
the contact base during brewing! Never try to remo-
ve or re-adjust the coffee pot and the water tank or
perform similar operations during the operation of
the espresso maker!
rubber gasket or the electric cord has become damaged.
Operation
Making 6 cups of espresso:
it to the brim with ground espresso powder.
do not press the powder deeper into the filter.
for a perfect seal along the gasket.
water tank and tighten it by turning it clockwise.
ter tank must be at least above each other or if possi-
ble tighten a little further.
tightly to prevent any steam from escaping.
tact base.
goes out.
cool off first.
to clause cleaning.
CAUTION!
The housing of the espresso maker is
hot! Grab the pot only by its handle!
EN
9