Power level
The power level of the cooking area can be set from level 1
to level 9.
Special functions
By turning on the touch display, you can program a special
function by pressing the button indicating the position of the
cooking area.
This function is available to "assist cooking" in each cooking
area and is indicated by one of the three dedicated icons.
It is possible to activate 3 "cooking" levels:
1)
Melting with a temperature of approximately 42 °C.
2)
Heating with a temperature of approximately 70 °C.
3)
Simmering with a temperature of approximately 94 °C.
These temperatures are approximate and are greatly
dependent on the pot and the quantity of food.
Control lock (child safety)
It is only activated when the cooking surface is on but no
cooking area is on.
Press the key button (5) and the pause button (6) and then lock
the key button (5).
The corresponding control lock LED will light up.
When you try to turn on the cooking surface with the On/Off
button (1), the "lock" and "ON" LEDs will light up at the same
time and it will not be possible to cook.
Unlocking/deactivation child safety
To permanently remove the "lock", turn the piano on with the
button ON, then hold down the "lock" button.
Pause
This cooking surface allows setting a pause (6) during cooking
(which is useful, for example, when answering a phone call).
When this function is pressed, an LED lights above the button
and the symbol "II" is displayed in all the cooking areas and
the cooking settings and timers are frozen for a maximum of
10 minutes, after which the cooking surface turns off.
Deactivating Pause
Once activated, the function can be deactivated by pressing
the pause button (6) again. The LED for the pause setting turns
off and, within 10 seconds, you must slide your finger along
the cursor below the illuminated area (from left to right). This
allows the surface to resume cooking and the timer starts from
the same point at which it was stopped.
Timer function
There are two versions of the timer function:
• An independent timer from 1 to 59 minutes: it beeps when
the time has run out. This function is always available and
is indicated by the clock symbol (24) which is located
between the - and + buttons (the symbol may be less bright
if another cooking area timer has a remaining time that is
less than that set on the independent timer).
• A timer from 1 to 59 minutes for each cooking area: it beeps
when the time has run out and turns off the cooking area
where it was set. The 4 cooking areas can be programmed
independently (the symbol may be less bright if another
cooking area timer has a remaining time that is less than
that set on the independent timer).
The type of timer activated is shown in the dedicated displays
(19-20-21-22). The timer with the least time is highlighted
and the related clock icon is brighter (13-24). The other timer
settings are still active and running, but the clock icon (13-24)
will be less bright.
Another icon with the word "min" (23) appears when you set
times longer than 10 minutes. For example 0.11 indicates 0
hours and 11 minutes.
The separator dot (21) flashes when the timer is running, while
the dot is static while the timer is selected and thus modifiable.
Independent timer
• If the touch display is on, the independent timer can be
used by simultaneously pressing the + and - buttons. If all
the cooking areas are in position "0", this is the only timer
available. The clock icon (24) will turn on and the display
will show "0.00". If you do not select any button, the timer
deactivates within 5 seconds.
• The time setting (0-1hour.59min) can be changed in
increments of one minute with the + button from 0 to 99.
• Holding down the + or - button dynamically increases the
rate of change up to a maximum value, without beeps.
• If the + (or -) button is released, the rate of increase (decrease)
starts again from the initial value.
• The timer can be set by either continuously pressing the +
or - buttons or by pressing successively (with beeps).
• After the timer is set, it begins to count down. The expiry of
the time is signalled by a beep or by the flashing of the timer
display, which will show "00".
• The beep will not stop until the + or - button is pressed. The
display stops flashing and turns off.
Turning off/changing the timer
• The timer can be changed or turned off at any time by
turning on the touch display again, if no cooking area is
on, and pressing the + and - buttons simultaneously to select
the timer. At this point, set it to "0" by pressing the - button,
to turn it off, or by pressing the + button to increase the time
setting.
• The independent timer remains active even when the On/
Off button is pressed
EN
7