Useful Information; Wireless Controller (Wico); Menu Button - IKA EUROSTAR 200 control Instrucciones De Manejo

If the Bluetooth ® function of the Wireless Controller is active, the
user can use the Bluetooth
®
Wireless Controller. A beep signal will be audible even if the Wire-
less Controller is switched off.
• Speed setting
You can use the rotary knob (B, see Fig. 1) to pre-set the required
speed before you start the device. If you then press the rotary
knob(B, see Fig. 1) the device starts at the speed you set. When
a change is made to the speed, the rated speed is shown in the
display (C, see Fig. 1). When the device is stopped, the button (K,
see Fig. 1) can be used to switch between the two speed ranges
(I and II). When in standby mode, the display (C, see Fig. 1) shows
the set speed.
The EUROSTAR 200 / 200 P4 control stirrer is controlled via a
Wireless Controller (WiCo). If the Wireless Controller is attached
to the EUROSTAR station, data exchange between the stirrer
(station) and Wireless Controller is performed via the contacts
(E, Q, see Fig. 1). "Home" symbol
the Wireless Controller. If the Wireless Controller is connected to
the stirrer (station) via a USB (Universal Serial Bus) cable, the
symbol appears. If the Wireless Controller is neither bolted to the
EUROSTAR station nor connected to the stirrer (station) via a
USB cable, the data exchange between the stirrer and Wireless
Controller is performed via Bluetooth
symbol is displayed.
Depending on the structure of the building, the Wireless Controller
can be operated at a distance of up to 150 m from the EUROSTAR
station, using the Bluetooth
Controls of the Wireless Controller (WiCo)
N
K
O
L
B
M
Working screen at the time of delivery:
The start screen appears for a few seconds after
B
0
the Wireless Controller is switched on. The de-
Torque: Ncm
 vice name and the software version are displayed.
Reset Torque Back
00:00:00
After this, the following working screen appears
Timer:
0
I automatically in the display.
actual rpm
Note: The wireless symbol
0
set rpm
the stirrer (station) is switched on.
Explanation of symbols on the working screen:
The symbols displayed change depending on the
B
100
status and settings of the Wireless Controller. The
Torque:
Ncm
45.0
Temp.: ºC
screen below shows the most significant symbols
99:00:00
Timer:
on the working screen.
300
I
00:00
actual rpm
PC
2000
LIMIT
controlled
rated rpm
search button (H) to search for the

Useful information

appears on the display of
® . In this case the Bluetooth
® connection.

Wireless Controller (WiCo)

Item Name
M ON/OFF button:
L key button:
N

Menu button:

B Rotary/push knob: Navigation, selecting and changing the settings in the menu
O Back button:
K Gear button:
appears only when
The stirrer has two different speed ranges:
Range I: low speed, high torque.
Range II: high speed, low torque.
• Correct procedure for changing the speed range:
- Switch the device off at the rotary knob (B, see Fig. 1)
- Switch the speed range with button (K, see Fig. 1)
- Change the speed with the rotary knob (B, see Fig. 1)
- Switch the device on at the rotary knob (B, see Fig. 1)
- The speed can be varied at any time in operation
- The speed appears in the display (C, see Fig. 1).
The Wireless Controller can be attached to the stirrer (station), or
can be installed in a safe place easily accessible by the user while
the stirrer is running.
If the Wireless Controller is attached to the EUROSTAR station,
the rechargeable battery is automatically recharged via the con-
tacts (Q, see Fig. 1). The rechargeable battery can also be charged
via the USB port of the Wireless Controller (see "Charging the
RB 1 battery pack (rechargeable battery)" in the "Securing"
section).
WARNING
®
rer using the screw (P, see Fig. 1), or positioned remotely from the
stirrer (station) whilst it is running.
Switching the Wireless Controller on and off
Disable button and rotary / push knob
Press it once: main menu is displayed
Press it a second time: back to the working screen
Return to the previous menu level / reset the torque
Change the gear in different speed/torque ranges
Note: Can be activated only when the station is in stand-by mode.
Bluetooth
This symbol means the EUROSTAR station and the Wireless
Controller are communicating via Bluetooth
The symbol no longer appears if no Bluetooth
being performed.
Key:
This symbol means that the function of the buttons and of the
rotary knob for controlling the Wireless Controller are disabled.
The symbol no longer appears if the functions are enabled once
again by pressing the key button a second time.
B Operating mode:
This symbol indicates the operating mode currently selected (A,
B, C).
If the stirrer (station) generates vibration, the
Wireless Controller must be bolted to the stir-
:
®
.
®
communication is
®
25