Operating Mode - IKA EUROSTAR 200 control Instrucciones De Manejo

Temperature
In the "Temperature" menu the user can specify that the tem-
perature sensor is displayed on the display/working screen. A tick
shows that the option is activated. The precondition for this is that
a temperature sensor is connected to the EUROSTAR station. If
no temperature sensor is connected, or an error is present or the
temperature rises above 350 °C, three dashes are shown as the
temperature value.
Note: Please comply with the temperature measurement range of
the external temperature sensor specified in the "Technical data"
section. The temperature display can be in either °C or °F (see the
"Settings" menu).
Timer
In the "Timer" menu the user can specify that the timer is dis-
played on the display/working screen. A tick shows that the option
is activated. This setting allows the user to specify the actual time
for the stirring procedure.
A default time can also be set for the timer. This setting allows the
user to start the stirring task for a standard time. The device stops
automatically after expiry of the set time, and the set time used for
the stirring procedure appears in the display.
Note: The user can stop the stirring function before expiry of the
set time. In this case the countdown of the timer is interrupted.

Operating Mode

Operating Mode A:
In this operating mode, the set speed is not saved when the current
run comes to an end or the device is switched off.
Operating Mode B:
In this operating mode, the set speed is saved when the current
run comes to an end or the device is switched off, and the value
can be changed.
Operating mode C:
In this operating mode, the set speed is saved when the current
run comes to an end or the device is switched off, and the value
cannot be changed.
Display
In the "Display" menu the user can specify what information will
be displayed on the main screen.
Note: If the "Torque"option is activated, by pressing the "Back"
button the user can reset the current torque to 0 Ncm as a reference
value. At the same time the Δ appears in front of the Ncm unit.
Safety
Time Out:
In the "Time Out" menu, the user can set a time limit. This time
limit applies if there is a communication failure between the
EUROSTAR station and the Wireless Controller or the com-
munication range is exceeded. The EUROSTAR station will
continue to run at the set speed until the set time has expired.
After that the EUROSTAR stirrer (station) will continue to run
at the set safe speed (see the "Safe speed" menu).
Note: The initial setting for the time limit is 30 seconds. The user
can set a value of up to 60 minutes for this time limit.
If the intermittent mode is activated, the
CAUTION
EUROSTAR station immediately switches
to run at the set safe speed, or the set speed if that is less than
the safe speed.
Safe Speed:
In the "Safe Speed" menu, the user can specify a speed that is ap-
propriate and safe for the stirring task. The safe speed applies if there
is a communication failure between the EUROSTAR station and
the Wireless Controller or the communication range is exceeded.
Note: The initial setting of the safe speed is 100 rpm (EUROSTAR
200 control) and 50 rpm (EUROSTAR 200 P4 control), and is
implemented after expiry of the time limit (see "Time out").
Password:
In the "Password" menu, the user can protect the Wireless Control-
ler settings using a password (factory setting: 000).
Settings
Languages:
The "Languages" option allows the user to select the desired
language by turning and pressing the rotary/push knob (B). A tick
indicates the language that is set for the system.
Units:
The "Units" option allows the user to select the desired unit for
displaying the temperature. The choice is between "°C" or "°F"
and is made by turning and pressing the rotary/push knob (B). A
tick indicates the unit that is set for the system.
Display:
The "Display" option allows the user to change the background
color and brightness of the working screen.
Sound:
The "Sound" option allows the user to activate/deactivate the
key-press sound and to set the volume.
Factory Settings:
Select the "Factory Settings" option by turning and pressing
the rotary/push knob. The system requests confirmation to recre-
ate the factory settings. Pressing the "OK" button resets all the
system settings to the original standard values set at dispatch
from the factory (see "Menu structure").
Bluetooth :
®
The "Bluetooth " option allows the user to activate/deactivate
®
the "Bluetooth " function. A tick shows that the option is ac-
®
tivated.
Information:
The "Information" option offers the user an overview of the
most important system settings of the stirrer EUROSTAR 200 /
200 P4 control.
29