Building Instructions - Multiplex Movie Star Pico line Instrucciones De Montaje

MovieStar
1. Examine your kit carefully!
MULTIPLEX models are subject to constant quality checks throughout the production process, and we sincerely hope that
you are happy with the contents of your kit. However, we would ask you to check all the parts before you start construction, with
reference to the parts list, as we cannot exchange components which you have already worked on. If you find any part is not
acceptable for any reason, we will readily correct or exchange it once we have examined it. Just send the component to our
Model Department. Please be sure to include a brief description of the fault.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents
in terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that
we cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings in the normal sense of the word.
Building and operating them safely requires a certain level of technical competence and manual skill, together with
discipline and a responsible attitude at the flying field. Errors and carelessness in building and flying the model can
result in serious personal injury and damage to property. Since we, as manufacturers, have no control over the
construction, maintenance and operation of our products, we are obliged to take this opportunity to point out these
hazards, and to emphasise your personal responsibility.
Additional items required:
Radio control system components:
PiCO "Brick" (2 servos, 1 receiver, 1 switch in block)
Elevator / rudder
PiCO Control 400 Duo speed controller
Alternatively:
MULTIPLEX Micro IPD receiver
MULTIPLEX MS-X3 servo (2 reqd.), ele./rudd.
PiCO-Control 400 Duo speed controller
Flight batteries:
MULTIPLEX 7/1700 SCR drive battery
or MULTIPLEX 8/3000 SCR-C drive battery
If you intend flying the model with an additional payload we recommend using eight cells; you may need to arrange them
four cells above four cells to obtain the correct CG. We also recommend the optional gearbox conversion set, Order No.
33 2693.
Battery charger:
PiCO AUTO-Lader for fast-charging transmitter and flight packs
Adhesives:
MULTIPOXY 5-Minute epoxy 100 g, or similar product
MULTIPLEX ZACKI, medium-viscosity
10 g (cyano-acrylate), or similar product
MULTIPLEX Activator, or similar product
Tools:
Scissors, combination pliers, balsa knife, screwdrivers (flat blade and cross-point), 120-grit abrasive paper, 2.5 and 7
mm Ø twist drills.
Specification: MOVIE STAR
Wingspan
Fuselage length
Wing area (FAI) approx.
Weight approx.
Wing loading
Wing section
Tailplane section
Controls:
Important information - gluing foam components:
The "MOVIE STAR" model is not made of styrofoam but ELAPOR! As adhesives we recommend cyano-acrylate ("cyano")
and contact cement such as UHU Kraftkleber or UHU POR. 5-minute epoxy should only be used in conjunction with a
coupling layer of cyano, with a sprinkling of micro-balloons. Cyano should always be used together with cyano activator.
Parts to be joined are wetted on one side with activator, which is then allowed to air-dry. Cyano (medium-viscosity type)
is applied to the opposite side, and the parts brought together. White glue is not suitable, and epoxy-based adhesives
should not be used without the coupling layer.
8

Building instructions

Order No. 21 4163
Order No. 1 4020
Order No. 7 5024
Order No. 5 5971
Order No. 6 5135
Order No. 7 5024
Order No. 15 5646
Order No. 15 6027
Order No. 9 2526
Order No. 60 3848
Order No. 59 2720
Order No. 59 2824
1400 mm
980 mm
38 dm²
1450 g
38 g/dm²
HQ 30-12 mod.
NACA 0009/0010
Rudder, elevator, motors