Installation - General - Franklin Electric E-Tech EV Serie Manual De Uso

Use and installation instruction manual
2.2 Motor rating plate
For electric pumps sold with standard motor, refer to the following instructions
(Fig. 3) for reading the motor rating plate.
For bare shaft pumps, refer to the manufacturer's manual.
A) Serial number
B) Year of production
C) Model identification code
D) Power frequency (in Hz)
E) Supply voltage, delta connection (in V)
F) Supply voltage, star connection (in V)
G) Machine IP protection rating
H) Maximum current, delta connection (in A)
I) Maximum current, star connection (in A)
J) Room temperature (in °C)
K) Motor weight
The motor is designed for continuous duty (class S1 according to IEC 60034-1).
2.3 Other plates and markings
On the surface of the pump, there may be other plates, depending on the model,
that identify its features, compliance with rules and regulations or installation, use
and disposal provisions. See the following list.
Pay attention to the risks associated with the product installation,
maintenance and disposal.
Before installing and using the electric pump, carefully read the
instruction manual.
Appliance approved for handling water intended for human
consumption (WRAS certificate number 1511053), up to a
maximum temperature of 85°C
Maximum liquid temperature for use in the home, residential,
commercial, agricultural or tertiary sector: 85°C.
Maximum liquid temperature EXCLUSIVELY for industrial use or
equivalent: 120°C.
Tmax 120°C
This marking identifies the high pressure pumps (special versions)
• The direction of rotation of the functional parts is indicated by the marking
(arrow) on the motor support, see fig. A3.
• The flow direction is indicated by the marking (arrow) on the pump base. See
fig. A3.
2.4 Motor energy efficiency information
All electric pumps use motors compliant with reg. 640/2009 EC and subsequent
amendments, therefore compliant with efficiency class IE3 (three-phase versions
with power greater than 0.55 kW). Additional information about motor energy
performance is available online (franklinwater.eu - product data sheet) and on
the motor rating plate.
2.5 Pump energy efficiency information
All pumps comply with Reg. (EC) No 547/2012. The MEI energy efficiency index
is greater than or equal to 0.4 (MEI Benchmark 0.7). Refer to the rating plate
and label attached to this manual for any information regarding the pump. The
machine performance curves, efficiency characteristics and energy performance
details are available online (franklinwater.eu - product data sheet).
3 APPLICATIONS AND USE
3.1 Permitted use
These appliances are designed for professional use in applications such as water
supply from groundwater, pressure increase, irrigation or heat transfer fluid
circulation. They can be used in the industrial, manufacturing or equivalent fields.
The electric pumps can also be used in the domestic, commercial, agricultural,
artisan or tertiary sectors, for the same applications, exclusively at a temperature
not exceeding 85°C.
NOTE: For other applications the maximum temperature allowed is 120°C.
Electric pumps must be installed in dry areas and protected from flooding.
The electric pump can work continuously at the maximum room temperature
indicated on the motor rating plate. For bare shaft pumps, follow the motor
manufacturer's indications.
3.2 Pumped liquids
Clean liquids, compatible with the electric pump component materials. A liquid
must have physical characteristics similar to those of clean water at room
temperature (1030 kg/m
Fig. 3
these limits are exceeded, contact the manufacturer).
Any sand content in the water must not exceed 50 g/m3. Higher sand
concentrations will reduce the electric pump service life and increase the risk of
blockage. Any suspended solids must not exceed 2 mm in maximum size.
Water intended for human consumption: only models with WRAS certification, at
a maximum temperature of 85°C.
3.3 Conditions of use
• Maximum operating pressure (pump delivery pressure, obtained by the sum of
• Flow rate and head: during normal operation they must fall within the fields
• Sucked liquid maximum temperature: 85°C or 120°C depending on use (see
• Sucked liquid minimum temperature: -30°C (EPDM gaskets); -10°C (Viton®/
• Room temperature: maximum 40°C up to 1000 m altitude. If these limits are
• Electrical supply voltage: refer to the motor rating plate. The maximum
• Maximum number of consecutive hourly start-ups: for electric pumps with
3.4 Non-permitted use
Do not use the electric pump for applications other than those described
above and, in any case, not authorised by the manufacturer. Improper use may
cause serious damage (including death) to people, animals, objects and the
environment.
• Do not pump food liquids or human food products.
• Do not pump any liquids that are more viscous and/or denser than water,
• Do not use the machine in potentially explosive environments or with
• Do not run the machine without any liquid.
• To avoid overheating, do not run the electric pump continuously at a flow rate
• Do not exceed the maximum pressure indicated on the rating plate.
3.5 Other uses
Contact the Manufacturer if:
• The liquid to be pumped has a viscosity or density higher than that of the water
• The water to be pumped is chemically treated (softened, chlorinated, purified,
• Any situation other than those listed under permitted use occurs.
4 INSTALLATION – GENERAL
The appliance must be installed in accordance with the instructions in this manual.
The appliance and terminals of the power supply cable must be protected against
water, humidity and atmospheric agents. Check the protection rating (IP)
indicated on the motor rating plate. Install in a location not subject to flooding.
maximum density and 2 cPs maximum viscosity. If
3
Improper use can result in overheating of the machine and power cables,
with consequences such as failure and potentially fire.
the pump inlet pressure and the pressure increase supplied by the pump): see
the rating plate. The maximum pressure at the appliance inlet is determined by
the pressure increase created by the pump, so as not to exceed the maximum
operating pressure (see the section dedicated to the calculation).
indicated on the rating plate. Under these conditions, optimal machine
operation is achieved.
paragraph 3.1).
FKM gaskets)
exceeded, contact the manufacturer.
deviation allowed is 6%.
standard motor, see fig. A4 (in the appendix). For bare shaft pumps, follow the
instructions of the motor manufacturer.
Do not use the electric pump connected to swimming pools, basins,
ponds and in similar places when people are immersed in water.
unless specifically authorised by the Manufacturer.
flammable liquids.
of zero or lower than 10% of the rated value. If the temperature of the inlet
liquid exceeds 90°C, increase the minimum flow rate to 20% of the nominal
value.
(it will be necessary to use a motor with a proportionally greater power)
etc.)
Before starting work on the machine, make sure that it has been
disconnected from the power supply network and that it cannot be
accidentally reconnected.
ENGLISH
11