miniland baby digimonitor 3.5 plus Manual De Instrucciones página 22

If the charger remains connected to the mains but
the charging process is complete, the charging LED
indicator (3) will light in green.
When the level of battery is low, the battery level icon
(i) will begin to blink in red and the monitor will start to
beep every 30 seconds.
Note: remove the battery when the appliance is
not going to be used for a prolonged time period.
5.1.2. BABY UNIT POWER SUPPLY
The camera or baby unit of this baby monitor is
designed for use with the AC/DC adapter supplied.
1. Place the connector socket (VII) at the rear of the
baby unit.
2. Connect the adapter cable to the mini-USB socket
of the camera. Only use the adapter supplied.
3. Plug in the adapter to the mains.
Warning: Danger of Strangulation – Keep the
cable out of reach of the baby. NEVER place a
camera with cables less than 1 metre away from
the cot. Never use extension cables with AC
adapters. Only use the AC adapters supplied.
5.2. OPERATION
5.2.1. TURNING THE UNITS ON/OFF
5.2.1.1. MONITOR:
Keep the ON button pressed (5) situated on the upper
part of the monitor to turn it on and off. The ON/pairing
LED indicator (1) will go on and off depending on whether
you turn the unit on or off.
5.2.1.2. CAMERA:
To turn the camera on or off, keep the on button (III)
pressed in for two seconds. The power
LED (IX) will go on and off depending on whether you
turn the unit on or off.
When you have installed the camera and turned it
on, you can see the images and listen to the sounds
captured in your baby's room via the monitor.
5.2.2. MONITOR VOLUME
Press the set button
volume of your monitor or the set button
wish to turn it down, choosing between the 5 levels
available.
5.2.3. TALK TO THE BABY
You may talk to your baby from the parents' unit (for
example, to calm it down and so it understands you'll
be with it in a moment) or to your partner (if he or she
is in the baby's room).
Press the button and keep it pressed in to talk to the
baby (12) and talk in front of the monitor. Release the
button when you have finished talking to listen to the
sound from the baby's room again.
Bear in mind that you can't listen to your baby whilst
you're talking to it; to listen to it, you will have to stop
pressing this button.
5.2.4. ZOOM
You may increase the size of the image viewed,
carrying out a four-position zoom.
To use this function, follow the next steps:
1. Press the zoom button
function. The upper left quarter of the image will
appear in the white section.
(8) if you wish to increase the
(10) if you
. to access the zoom
2. Press the set UP
change the selected quarter.
button to increase the image of the
3. Press the
selected quarter.
4. Press the zoom button
quarter selection process in case you wish to zoom
onto another of the quarters.
5. Press the zoom button
function.
5.2.5. INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function enables the camera
to capture images of your baby or of the monitored
area when it is dark or there is little light.
In this mode images will only be shown on the monitor
in black and white and you will only be able to see
images situated less than 2 meters away.
The camera constantly monitors the light level and
automatically switches to infrared mode when there is
not enough light for normal vision.
5.2.6. OUT OF RANGE WARNING
If the monitor is located at a distance away from the
camera which is greater than that allowed (see the
technical characteristics), the on/link LED indicator
of the camera (IX) and the monitor (1) will flash in
red, the coverage symbol (a) will appear red and the
screen will display the "MINILAND" logo screen.
Bring the monitor closer to the camera to see the
image correctly again.
5.2.7. MAIN MENU
Keep the Menu/Back
to make adjustments to the main functions and
characteristics of your baby monitor.
5.2.7.1. CAMERA MENU
5.2.7.1.1. CHOOSING THE CAMERA
This product is designed to allow the observation of
different areas with up to 4 cameras. To choose the
camera you want to see, follow the next steps:
1. Press for 3 seconds the Menu/Back
the menu will pop up;
2. Press the UP
camera icon is highlighted then press the
enter into the sub-menu.
3. Press the UP
camera icon is highlighted and then press the
key.
4. Press the UP
camera that you want to see and confirm the selection
key.
with the
Note 1: You will only be able to select the cameras
that have already been paired with the monitor.
Note 2: There is a faster way to change the camera
you are viewing. Directly press
through paired cameras: CAM1 / CAM2 / CAM3 /
CAM4 / SCAN MODE.
5.2.7.1.2. SCAN MODE
This function automatically cycles through your paired
camera channels to display each camera for 12
seconds. This function can be used only when you
have more than 1 camera unit paired.
To enter in this mode:
22
ENGLISH
(10) keys to
(8) or DOWN
and you will return to the
again to exit the zoom
button pressed in order
key or DOWN key until the
key or DOWN key until the SEE
key or DOWN key to select the
key to cycle
button and
key