Camera Settings Menu; Night Light - miniland baby digimonitor 3.5 plus Manual De Instrucciones

ENGLISH
1. Press for 3 seconds the Menu/Back
menu will pop up.
key or DOWN
2. Press the UP
camera icon is highlighted then press the
enter into the sub-menu.
key or DOWN
3. Press the UP
SEE camera icon is highlighted and then press the
key.
key or DOWN
4. Press the UP
the SCAN icon .
key to confirm.
5. Press the
Note 1: When one of the cameras is out of range or is
not switch on, the monitor will warn you and the Scan
Mode will stop.
Note 2: The Scan mode can be turned on or off by
pressing the button while viewing the main screen.
5.2.7.1.3. PAIRING CAMERA
This product is designed to allow the observation of
different areas with up to 4 cameras (channels 1, 2, 3
or 4 assigned to different cameras). The monitor and
the original camera leave the factory with channel 1
programmed. If you need to add an extra camera,
follow the process set out below.
1. Press for 3 seconds the Menu/Back
menu will pop up.
key or DOWN
2. Press the UP
camera icon is highlighted then press the
enter into the sub-menu.
key or DOWN
3. Press the UP
add camera icon is highlighted and then press the
key.
key or DOWN
4. Press the UP
channel where you want to add the new camera and
confirm the selection with the
5. While the ON/pairing LED indicator (1) is flashing in
green, press the link button on the camera (VI).
6. Once paired, the LED indicator will stop flashing
and the image of the camera will show immediately
on the monitor unit screen.
7. If unsuccessful, please repeat above steps.
Note 1: You will only be able to select the channels
where no camera has been paired yet.
Note 2: It is not possible to enter this submenu if 4
cameras have already been paired.
For various reasons you may lose the connection
between the monitor and a camera which is already
connected. Should this be the case, repeat the
process explained above to connect the camera with
the monitor again.
5.2.7.1.4. DELETE CAMERA
To delete one of the cameras connected, follow the
next steps:
1. Press for 3 seconds the Menu/Back
menu will pop up.
key or DOWN
2. Press the UP
camera icon is highlighted then press the
enter into the sub-menu.
key or DOWN
3. Press the UP
remove camera icon
key and the
key until the
key
key until the
key and select
key and the
key until the
key
key until the
key to select the
key.
key and the
key until the
key
key until the
is highlighted and then
key.
press the
key or DOWN
4. Press the UP
camera you want to delete and confirm the selection
key.
with the
Note 1: If you only have one camera paired to the
monitor, you won't be able to remove it and you won't
be allowed to enter this submenu.
Note 2: A channel needs to be deleted before pairing
to a new camera unit.

5.2.7.2. CAMERA SETTINGS MENU

5.2.7.2.1. LULLABIES
You can soothe the baby to sleep by playing a gentle
lullaby from the baby unit. To activate this function:
1. Press for 3 seconds the Menu/Back
menu will pop up.
2. Press the UP
camera settings menu icon
key enter into the sub-menu.
press the
3. Press the UP
lullaby icon
is highlighted then press the
enter into the sub-menu.
4. Press the UP
one of the 5 available lullabies, silence or loop
reproduction (default OFF).
5. When you have selected the tune, press the
and the volume control will appear. Press the UP
DOWN key to select the level of volume from 1 to 3
key.
and press the
6. Press the Menu/Back
to the main screen.
7. Lullaby icon (d) will be displayed at the top of the
LCD screen.
Keep in mind that the configuration of the lullabies will
take place only on the camera that is being watched
in that moment.
Note: Lullaby loop function plays in cycle all the
lullabies.
5.2.7.2.2. CAMERA VOLUME
This menu will allow you to configure the volume level
at which the parents' voices will be reproduced on the
camera by using the two-way function.
In order to configure the camera volume, follow the
next steps:
1. Press for 3 seconds the Menu/Back
menu will pop up.
2. Press the UP
camera settings menu icon
key enter into the sub-menu.
press the
3. Press the UP
camera volume icon
key;
the
4. Press the UP
whichever of the three camera volume levels available
(HIGH/MID/LOW) you prefer.
5. Confirm the selection pressing the
Bear in mind that the volume will only be configured
for the camera whose image you are viewing on the
monitor at that time.

5.2.7.2.3. NIGHT LIGHT

The baby unit has a nightlight which emits a soft light,
23
key to select the
key and the
key or DOWN key until the
is highlighted then
key or DOWN key until the
key or DOWN key to select
key three times to return
key and the
key or DOWN key until the
is highlighted. Then
key or DOWN key until the
is highlighted. Then, press
key or DOWN key, choose
key.
key
key
/