Notes regarding ovenware
Suitable ovenware
Suitable dishes are heat-resistant ovenware made of glass,
glass ceramic, porcelain, ceramic or heat-resistant plastic.
These materials allow microwaves to pass through.
You can also use serving dishes. This saves you having to
transfer food from one dish to another. You should only use
ovenware with decorative gold or silver trim if the manufacturer
guarantees that they are suitable for use in microwaves.
Unsuitable ovenware
Metal ovenware is unsuitable. Metal does not allow microwaves
to pass through. Food in covered metal containers will remain
cold.
Caution!
Creation of sparks: metal – e.g. a spoon in a glass – must be
kept at least 2 cm from the oven walls and the inside of the
door. Sparks could destroy the glass on the inside of the door.
Ovenware test
Do not switch on the microwave unless there is food inside. The
following ovenware test is the only exception to this rule.
Perform the following test if you are unsure whether your
ovenware is suitable for use in the microwave:
Heat the empty ovenware at maximum power for ½ to
1.
1 minute.
Check the temperature occasionally during that time.
2.
The ovenware should still be cold or warm to the touch.
The ovenware is unsuitable if it becomes hot or sparks are
generated.
Microwave power settings
Use the button to set the desired microwave power.
90 W
for defrosting delicate foods
180 W
for defrosting and continued cooking
360 W
for cooking meat and heating delicate foods
600 W
for heating and cooking food
1000 W
for heating liquids
Microwave combi operation
This involves the simultaneous operation of another operating
mode with the microwave. Using the microwave makes your
meals ready more quickly, but they are still nicely browned.
In this section, you will read about
which operating modes are suitable
■
how to set the microwave combi mode
■
Suitable types of heating
■
Suitable types of heating
3
Hot air
■
4
Hot air grilling
■
Circulated air grilling
=
■
Note: Rapid heat up cannot be switched on in microwave
combination mode.
Suitable microwave power settings
All microwave power settings, except for 1000 watts, can be
combined with an operating mode.
34
Notes
When you press a button, the selected power lights up.
■
The microwave power can be set to 1000 watts for a
■
maximum of 30 minutes. With all other power settings a
maximum cooking time of 1 hour 30 minutes is possible.
Setting the microwave
Example: microwave power 600 W, cooking time 10 minutes.
Press the operating mode selector.
1.
The appliance is ready for operation.
Press the button for the microwave power setting you require.
2.
The selected power setting lights up and a suggested
cooking time is displayed.
Set the cooking time using the rotary selector.
3.
Press the
button.
ƒ
4.
The operation starts. The cooking time starts counting down.
The cooking time has elapsed
A signal sounds. Microwave operation has finished. You can
stop the audible signal by pressing the
reset the appliance.
Opening the appliance door during operation
Operation is suspended. The cooling fan may continue to run.
After closing the door, press the
continue.
Changing the cooking time
Change the cooking time using the rotary selector.
Changing the microwave power setting
Press the button for the new microwave power setting. Use the
rotary selector to set the cooking time and restart.
Cancelling operation
Press the illuminated button for the set microwave power
setting. Make new settings or switch off the appliance.
Note: If you open the appliance door during cooking, the fan
may continue running.
Setting Microwave Combi operation
Example:
Microwave 360 W, 17 minutes and circulated air grilling
180 °C.
Set the operating mode using the operating mode selector
1.
and the temperature using the temperature selector.
Press the button for the microwave power setting you require.
2.
A suggested cooking time appears.
Set the cooking time using the rotary selector.
3.
Press the
button.
ƒ
4.
The operation starts. The cooking time starts counting down.
The cooking time has elapsed.
A signal sounds. Combination mode has finished. You can use
the
button to cancel the signal before the time has elapsed
Ã
and switch the appliance off or make new settings using the
operating mode selector.
Ã
button. Switch off or
ƒ
button. Operation will then
=