Murray 629108x61D Manual De Instrucciones página 16

5.
(Figure 18) Loosen the belt guide (9). Pull
the belt guide (5) away from the auger
drive pulley (10).
6. Pull the idler pulley (3) away from the au-
ger drive belt (4).
7. Remove the old auger drive belt (4) from
the auger drive pulley (10) and from the en-
gine pulley (11), Replace the auger drive
belt (4) with an original factory replacement
belt available from an authorized service
center.
8. Install the new auger drive belt (4) onto the
auger drive pulley (10) and onto pulley
(11).
9. Adjust the auger drive belt (4). See "How To
Adjust The Auger Drive Belt" in the Mainte-
nance section.
10.Adjust the belt guide (9). See "How To Ad-
just The Belt Guide" in the Maintenance sec-
tion.
11. (Figure 17) Install the belt cover (1). Tighten
screw (2).
12, Check the adjustment of the cables, See
"How To Check And Adjust The Cables" in
the Maintenance section,
13, Connect the spark plug wire.
How To Remove the Traction Drive Belt
If the snow thrower will not move forward, check
the traction drive belt for wear or damage. If the
traction drive belt is worn or damaged, replace
the belt as follows.
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See "How To
Remove The Auger Drive Belt" in the Mainte-
nance section.
3. (Figure 18) Remove the e-ring (17)from
one end of the swing plate axle rod (18).
Remove the swing plate axle rod (18) to
allow the the swing plate to pivot forward,
4. Remove the traction drive spring (16).
5. Remove the old traction drive belt (13) from
the traction drive pulley (14) and from the
engine pulley (15). Replace the traction
drive belt (13) with an original factory re-
placement belt available from an authorized
service center.
6. Install the new traction drive belt (13) onto
the traction drive pulley (14) and onto en-
gine pulley (15).
7. Make sure the traction drive idler pulley
(12) is properly aligned with the traction
drive belt (13).
8. Attach the traction drive spring (16).
9. Install the swing plate axle rod (18) and se-
cure with the e-ring (17) removed earlier.
lO,(Figure 28) The bottom of the swing plate
(20) must be positioned between the align-
merit tabs (19). Make sure the swing plate
(20) is properly secured.
NOTE: If the drive will not engage after
the traction drive belt has been replaced,
then check to make sure that the swing
plate is positioned between the alignment
tabs (19).
11, (Figure 18) Install and adjust the auger
drive belt (4), See "How To Remove The
Auger Drive Belt" in the Maintenance section.
12.Adjust the belt guide (9). See "How To Ad-
just The Belt Guide" in the Maintenance sec-
tion.
13.(Figure 20) Install the bottom panel (2).
F-031065L
14.Tighten the bolts (3) on each side of the bot-
tom panel (2).
15.(Figure 17) Install the belt cover (1). Tighten
screw (2).
16. Check the adjustment of the cables. See
"How To Check And Adjust The Cables" in
the Maintenance section.
17. Connect the spark plug wire.
How To Adjust The Belt Guide
1. Disconnect spark plug wire.
2. (Figure 17) Remove screw (2). Remove the
belt cover (1).
3. (Figure 2) Engage the auger drive lever (5).
4. (Figure 21) Measure the distance between
the belt guide (2) and auger drive belt (3).
The correct distance (4) is 1/8 inch (3.175
ram),
5. If an adjustment is necessary, loosen the
mounting bolt for the belt guide (2). Move
the belt guide (2) to the correct position
(4). Tighten the mounting bolt for the belt
guide (2).
6, (Figure 17) Install the belt cover (1), Tighten
screw (2).
7, Connect the spark plug wire.
How To Adjust Or Replace The Friction
Wheel
How To Check The Friction Wheel
If the snow thrower will not move forward, check
the traction drive belt, the traction drive cable or
the friction wheel. If the friction wheel is worn or
damaged, it must be replaced. See "How To
Replace the Friction Wheel" in this section. If the
friction wheel is not worn or damaged, check as
follows.
1. (Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
_k ARNING: Drain the gasoline out-
doors, away from fire or flame.
2, Disconnect the spark plug wire,
3, (Figure 20) Remove the bolts (1) on each
side of the bottom panel (2),
4, Loosen the bolts (3) on each side of the bot-
tom panel (2).
5, Remove the bottom panel (2),
6, (Figure 2) Position the shift speed lever (6)
in the lowest forward speed.
7. (Figure 22) Note the position of the friction
wheel (4). The correct distance "A" from the
right side of the friction wheel (4) to the out-
side of the motorbox is as follows:
Tire Size Distance "A"
12 and 13 inch 4-1/8" (10.5 cm.)
16 inch 4-5/16" (10.95 cm.)
If the friction wheel (4) is not in the correct
position, adjust as follows.
How To Adjust The Friction Wheel
1, (Figure 8) Loosen the nut (9) on the speed
control rod (2),
2, Remove the fasteners (8) to disconnect the
ball joint (6) from the shift yoke assembly
(7). To lengthen or shorten the speed con-
trol rod (2), turn the adapter (10) to obtain
the correct friction wheel position.
16
ENGLISH
3, Assemble the ball joint (6) to the shift yoke
assembly (7) with the fasteners (8).
4, Tighten nut (9) on the speed control rod
(2).
5, Make sure the speed select lever (1) func-
tions correctly, Move the speed select lever
(1) through all speeds.
6. (Figure 20) Install the bottom panel (2).
7. Tighten the bolts (3) on each side of the bot-
tom panel (2).
8, install the bolts (1) on each side of the bot-
tom panel (2).
How To Replace The Friction Wheel
If the friction wheel is worn or damaged, the
snow thrower will not move forward. The friction
wheel must be replaced as follows.
1. (Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
_IL ARNING: Drain the gasoline out-
doors, away from fire or flame.
2. Disconnect the spark plug wire.
3. (Figure 26) Remove the fasteners that se-
cure the right wheel (10). Remove the right
wheel (10) from the axle (11).
4. Loosen the bolts (3) on each side of the bot-
tom panel (2).
5, Remove the bottom panel (2),
6, (Figure 27) Remove the fasteners that se-
cure the drive sprocket (12) to the axle (11).
7, Remove the left wbeel, axle (11), and drive
sprocket (12).
8, (Figure 28) Remove the four bolts (16) that
hold the bearings (7) on each side of the
hax shaft (8),
9, (Figure 29) Remove the hex shaft (8) and
bearings (7).
NOTE: Take special note of the position of
the washers (17).
lO.(Figure 24) Remove the three fasteners (4)
that hold the friction wheel (5) to the hub
(6).
11, (Figure 24) Remove the friction wheel (5)
from the hub (6), Slip the friction wheel (5)
off the hex shaft (8).
12.Assemble the new friction wheel (5) onto
hub (5) with the fasteners removed eadier.
13.(Figure 29) Install the hex shaft (8) and
bearings (7) with the four bolts removed ear-
lier.
Make sure the washers (17) are properly
installed in the original position. Also,
make sure the two washers (13) are prop-
erly aligned with the actuator arms (14).
14.Make sure the hex shaft (8) turns freely.
15.(Figure 27) Install the ]eft wheel, axle (11),
and drive sprocket (12) with the fasteners
removed earlier. Install the chain (15) onto
the drive sprocket (12).
16.Check the adjustment of the friction wheel
See "How To Adjust The Friction Wheel" in
this section.
17.Make sure the fdction wheel and the disc
drive plate are free from grease or oil.
18.(Figure 20) Install the bottom panel (2).
19.Tighten the bolts (3) on each side of the bot-
tom panel (2).
20.Install the right wheel (10) to the axle (11)
with the fasteners removed earlier.
21 .Connect the spark plug wire.