Publicidad
SAFETY FIRST!
WARNINGS
DO's AND DO NOT's
WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING
INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY.
DO
read this entire operator's manual before operating this machine. Understand all warnings, instructions,
and controls.
DO
keep all guards in place and in good condition.
DO
wear safety approved hearing, eye, head and respiratory protection.
DO
read and understand all warnings and instructions on the machine.
DO
read and understand the symbol definitions contained in this manual.
DO
keep all parts of your body away from the blade and all other moving parts.
DO
know how to stop the machine quickly in case of emergency.
DO
shut off the engine and allow it to cool before refueling.
DO
inspect the blade, flanges and shafts for damage before installing the blade.
DO
use high-speed, reinforced, abrasive blades - 1/8" (3.17mm) thick (minimum) or high-speed, diamond
blades specifically rated with a maximum operating speed of at least 5400 RPM on 14" (350mm) or
6200 RPM on 12" (300mm).
DO
use high-speed reinforced, abrasive blades or high-speed, diamond blades marked with a 1" (25.4mm)
hole for a 1" (25.4mm) flange, or a 20mm hole for a 20mm flange.
DO
use abrasive blades or high-speed diamond blades marked for use with gasoline-powered, hand-held,
portable, abrasive cutting-off machines.
DO
read all safety materials and instructions that accompany any blade used with this saw.
DO
inspect each blade carefully before using it. If there are any signs of damage or unusual wear, DO NOT
USE THE BLADE.
DO
verify the blade arbor hole matches the machine spindle before mounting the blade.
DO
mount the blade solidly and firmly. Wrench tighten the arbor nut.
DO
make sure the blade and flanges are clean and free of dirt and debris before mounting the blade on the
saw.
DO
use the correct blade for the type of work being done. Check with blade manufacturer if you do not know
if blade is correct.
DO
always hold the machine with both hands when the engine is running. Use a firm grip with thumbs and
fingers encircling the handles.
DO
keep all parts of the body away from the cutting-off blades when the engine is running.
DO
keep the handles dry, clean and free of oil or fuel.
DO
always carry the machine with the engine stopped and the muffler away from the body.
DO
use caution and follow the instructions when loading and unloading the saw.
DO
operate this machine only in well ventilated areas.
DO
instruct bystanders on where to stand while the saw is in operation.
DO
establish a training program for all operators of this machine.
DO
clear the work area of unnecessary people. Never allow anyone to stand in front of or behind the blade
while the engine is running. Do use caution when handling fuel.
DO
move the machine at least 10 feet away from the fueling point before starting the engine and make sure
the gas cap on the saw and the fuel can are properly tightened.
DO
make sure the blade is not contacting anything before starting the engine.
DO
use cautions when lifting and transporting this machine.
English
Safety Precautions
DO
always check for buried electrical cables before sawing. If unsure, contact the local utilities.
DO
have all service, other than items in this manual, performed by competent service personnel.
DO
always tie down the machine when transporting.
DO
use caution and follow instructions when setting up or transporting the machine.
DO
clean the machine after each day's use.
DO
always give a copy of this manual to the equipment user.
DO NOT operate this machine unless you have read and understand this operator's manual.
DO NOT operate this machine without the blade guard, or other protective guards in place.
DO NOT stand behind or in front of the blade path while the engine is running.
DO NOT leave this machine unattended while the engine is running.
DO NOT operate this machine when you are tired or fatigued.
DO NOT use abrasive blades that are less the 1/8" (3.17mm) thick.
DO NOT exceed maximum blade speed shown for each blade size. Excessive speed could result in blade
breakage.
DO NOT use damaged equipment or blades.
DO NOT try to stop a moving blade with your hand.
DO NOT use an abrasive blade that has been dropped.
DO NOT use carbide-tipped or toothed type blades of any kind.
DO NOT use segmented diamond blades unless they are specifically designed for high-speed, hand-held saws.
DO NOT place 1 inch (25.4mm) arbor hole blades on 20mm flanges.
DO NOT grind on the side of a cutting-off blade.
DO NOT cock, jam or wedge the blade in the cut.
DO NOT operate a cutting machine if the blade does not stop rotating when the throttle trigger is released.
DO NOT start cutting until you have a clear work area and secure footing.
DO NOT allow other persons to be near the machine when starting, refueling, or when the saw is operating.
DO NOT operate the machine in the vicinity of anything that is flammable. Sparks could cause a fire or an
explosion.
DO NOT allow bystanders or animals in the work area while using a cutting-off machine.
DO NOT operate the saw while using drugs or alcohol.
DO NOT touch a dry cutting diamond blade immediately after use. These blades require several minutes to
cool after each cut.
DO NOT use damaged or worn blade flanges.
DO NOT operate this machine in an enclosed area unless it is properly ventilated.
DO NOT allow blade exposure from the guard to be more than 180 degrees.
DO NOT operate this saw without both hands on the handles.
This saw was designed for certain applications only. DO NOT modify this saw or use for any
application other than for which is it was designed. If you have any questions relative to its
application, DO NOT use the saw until you advised you.
*****************
15
Publicidad
