Routine Checks - Virtus CUTTER 06 Manual Del Usuario

and safety of the mixer To ensure regular and constant operation and to avoid invali-
dation of the warranty, machine components must be replaced only with original spare
parts.
8.3 - Checks carried out at our manufacturing plant
The manufacturer has conducted a number of tests on the machine in your posses-
sion, in order to ensure correct commissioning and include the necessary adjust-
ments.
In particular, the manufacturer has performed the following checks:
Before commissioning:
- Control of the operating voltage of the machine: the voltage must be the same re-
quested by the buyer.
- Checking for the presence of all the warning signs/labels and the rating plate with
the technical specifications and serial number.
- Checking of tightness of all bolts and nuts.
- Compliance of the machine to the applicable regulations/standards and to the in-
structions provided in this manual.
With the machine in operation:
- Checking of the efficiency of the safety devices and guard; the machine must stop
when the operator opens the grille.
- General operating control.
- Execution of repeated tests in order to verify the machine's set-up, according to the
type of work it will be used for.
8.4 - Checks and inspections to be carried out during installation
To make sure that the machine has not been damaged during transport or installation,
make sure that you diligently perform the checks and inspections listed below:
Before commissioning:
- Check that the voltage corresponds to the value shown on the machine identifica-
tion plate.
- Check for the presence and integrity of the warning and danger signs/labels.
- Check the integrity of the power cable.
- Check that the safety devices, such as magnetic sensors, are intact.
Checks with machine in operation:
- Check the efficiency of the safety guards and devices. These may have been dam-
aged or impaired during transport.
- Perform a few test runs with products of the same size of the material you will then
process.

8.5 - Routine checks

To maintain the features and reliability of your machine consistent over time, you
should perform additional checks and inspections (besides those described hitherto)
with the frequency listed below.
Before each work shift:
- Check the operation of the safety devices - daily.
-
Check the integrity of the power cable.
IMPORTANT!
If the machine does not stop when you open the lid or in the event of other malfunc-
tions, request the assistance of customer service.
24
1 Delivery and warranty
1.1 - Introduction
The symbols used in this manual are meant to draw the reader's attention to a set of
points and operations that are potentially dangerous to the personal safety of opera-
tors or that entail the risk of damaging the machine. Do not operate the machine
unless you are certain that you fully understand the instructions and guidelines high-
lighted in the notes.
IMPORTANT!
For the sake of clarity, some illustrations in this manual depict the machine or parts of
it with the panels or casings removed. Do not use the machine under such conditions,
but only if all of the guards are assembled correctly and are working perfectly. The
manufacturer prohibits the reproduction, even partial, of this manual, and its contents
may not be used for any purpose other than those explicitly authorised by the manu-
facturer. Any infringement will be prosecuted according to law.
1.2 - Storage and use of the manual
The purpose of this manual is to inform the users of the machine by means of texts
and detailed illustrations of the rules and essential guidelines for transporting, han-
dling, use and maintenance of the machine. Carefully read this manual before using
the machine.
Store it carefully near the machine, in a place that is easily and quickly accessible for
any future reference. If the manual is lost or damaged, request a copy from your
dealer or directly from the manufacturer.
In the event of transfer of the machine, be sure to inform the manufacturer of the con-
tact details and address of the new owner. The manual reflects the state of the art at
the time the machine was introduced on the market and cannot be considered inade-
quate if updated versions are issued as a result of technological progress. Regarding
the above, the manufacturer reserves the right to update the production and associ-
ated manuals without the obligation to update previous productions and manuals,
unless in exceptional cases.
In case of doubt, consult your nearest service centre or the manufacturer directly. The
manufacturer is committed to continuously improving the state of the art of its product
(s).
For this reason, the manufacturer welcomes any suggestions from its customers that
may help improve the machine and/or the manual. The machine was delivered to the
user under the warranty conditions valid at the time of purchase. Please contact your
supplier if you wish to receive clarifications or more information.
1.3 - Warranty
Under no circumstances is the user authorised to tamper with the machine. Should
you uncover malfunctions or flaws, contact the manufacturer. Any attempt to disas-
semble, modify or more generically tamper with any component of the machine by the
user or by unauthorised personnel will result in the revocation of the Declaration of
conformity issued pursuant to EC Directive 2006/42, will invalidate the warranty and
relieve the manufacturer of any liability for damages to persons and property caused
by such attempts.
The manufacturer shall also consider itself relieved of any responsibility in the follow-
ing cases:
5