Moretti Forni R Serie Manual Instrucciones página 21

6.3.8 REPLACING THE IGNITION CARDS
After carrying out the operations described in 6.1 above, to replace
the ignition cards proceed as follows:
- Remove the top rear panel by unfastening the four fixing screws;
- Disconnect the wires feeding the ignition card;
- Replace the ignition card (Plate A Item 24);
- Perform the above operations in reverse order to reassemble.
6.3.9 REPLACING THE TRANSFORMERS
After carrying out the operations described in 6.1 above, to replace
the transformer proceed as follows:
- Remove the top rear panel by unfastening the four fixing screws;
- Disconnect the wires feeding the transformer
- Replace the transformer, unfastening the lock nut in the case of the
toroidal version (Plate A Item 25). or the two screws in the case of
the other version (Plate A Item 47).
- Perform the above operations in reverse order to reassemble.
6.3.10 REPLACING THE TEMPERED GLASS
After carrying out the operations described in 6.1 above, to replace
the tempered glass proceed as follows:
Open the door;
- Remove the screws from the aesthetic frame inside the door;
- Unfasten the screws from the glass fixing frame.
- Remove the seal elements;
- Replace the glass (Plate A Item 01);
- Perform the above operations in reverse order to reassemble.
WARNING! Under no circumstances must the glass rest on or
come into contact with metal parts, so it is essential that a band
of ceramic fibre, of the same type fitted by the manufacturer, be
inserted at the bottom where the glass rests.
6.3.11 REPLACING THE SAFETY THERMOSTAT
WARNING! Regularly check that the safety thermostat is
operating correctly.
After carrying out the operations described in 6.1 above, to replace
the safety thermostat proceed as follows:
- Remove the front right side panel by unfastening the fixing screws;
- Open the door and remove the rotating carriage;
- Remove the thermostat sensor fixing plate by unfastening the fixing
screw located inside the baking chamber;
- Disconnect the thermostat faston connectors;
- Remove the thermostat dial;
- Unscrew thermostat lock nut;
- Replace the thermostat and the relative sensor (Plate A Item 19);
- Perform the above operations in reverse order to reassemble.
6.3.12 REPLACING THE
SAFETY THERMOSTAT
After carrying out the operations described in 6.1 above, to replace
the chimney extractor safety thermostat proceed as follows:
- Remove the sensor-bulb located in correspondence with the fume
extractor switch (chimney) after unfastening the lock screw;
- Remove the top rear panel by unfastening the fixing screws
- Remove the thermostat support bracket from the electrical
component panel;
- Replace the thermostat and the relative sensor (Plate A Item 26);
- Perform the above operations in reverse order to reassemble.
6.3.13 REPLACING THE CYCLE CARDS
After carrying out the operations described in 6.1 above, to replace
the cycle cards proceed as follows:
-Remove the top rear panel;
-Detach the cycle card connections;
- Disconnect the card from the omega bare and replace it (Plate A
Item 24);
- Perform the above operations in reverse order to reassemble.
6.3.14 GREASING THE CARRIAGE ROTATION BEARING
SUPPORT
NOTE! Abour every 6 MONTHS (this will vary according to the
type of equipment use) the carriage rotation support needs to be
greased.
After carrying out the operations described in point 6.1 above,
proceed as follows:
- Remove the top panel (Fig.16 item X);
CHIMNEY EXTRACTOR
- Grease the carriage rotation bearing support thoroughly with
LGHP2 SKF GREASE FOR HIGH TEMPERATURES via both
nipples (Fig.16 item G);
- Perform the above operations in reverse order to reassemble
6.4 DISMANTLING
When the appliance or its parts are dismantled, the various
components must be divided according to type of material, and then
disposed of in compliance with current laws and regulations.
7 SPARE PARTS
INDEX OF PLATES:
PLATE A=R14G Oven assembly.
PLATE B=R14G Wiring Diagram.
INSTRUCTIONS FOR ORDERING SPARE PARTS:
Orders for spare parts must contain the following information:
- SERIAL NUMBER
- TYPE OF APPLIANCE
- NAME OF PART
- QUANTITY REQUIRED
8 DRAWING REFERENCES
Fig.1 Working dimensions and weights
Fig.2 Oven identification
Fig.3 Labelling
Fig.4 Oven packing
Fig.5 Hook-up points to be used when lifting the oven (unloading)
Fig.6 Positioning the oven
Fig.7 Vapour exhaust connection
Fig.8 Combustion gas exhaust connection
Fig.9 Combustion gas exhaust connection
Fig.10 Connection to the electric power supply, water supply,
draining condensation, chimney thermostat and fan guard
reset.
Fig.11 Adjusting gas valve and exploded view of nozzle holder ramp
Fig.12 Control panel
Fig.13 Vapour extraction
Fig.14 Burner
Fig.15 Cleaning
UK8