Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
@5
CONT./SINGLE,
RELAY button
• CONT./SINGLE:
A short tap of this button will toggle between 3
possible END modes for playback.
CONT. (continue: plays all tracks) SINGLE (stops
playing and ReCUE's back to your original set
point), PLAYLOCK-see below.
• SINGLE PLAY LOCK:
SINGLE PLAY LOCK can be selected by
PRESET. When SINGLE PLAY LOCK is selected,
track selection during playback is disabled. This
prevents playback from stopping when the
Track Select Knob is turned accidentally during
playback. Play ending mode is the same as
single.
• RELAY:
You can turn on and off RELAY PLAY mode.
Relay playback is possible when two DN-
S3500s are connected by the MEMO in/out
jacks.
@6
FILE SEARCH MODE button
• MP3 DISC only:
When pushing this knob the file search
selection mode can be selected with the
PARAMETERS knob.
@7
TRACK/PARAMETERS knob
• TRACK:
When PARAMETERS LED is on, turn this knob
to select tracks.
By pushing this knob down while turning, the
tracks will change by 10 tracks at a time.
• PARAMETERS:
When the PARAMETER LED is flashing, turn
this knob to select and change the parameter
for items found in the Platter effects, Memo,
and Preset data, etc.
@8
NEXT TRACK button
• If this button is pushed during playback, the NEXT
TRACK mode will be selected. The next track can
be selected with the PARAMETERS knob.
@9
FAST SEARCH (
)
6
QUICK JUMP button
#0
FAST SEARCH (
)
7
QUICK JUMP button
• QUICK JUMP:
When one of these buttons is tapped shortly,
the playback position jumps approximately 10
seconds in the forward (
) or reverse (
7
direction. The jump time can be changed in the
preset mode.
• FAST SEARCH:
When one of these buttons is pressed and held
in, the disc is fast-searched in the forward (
or reverse (
) direction.
6
#1
PITCH BEND – button
#2
PITCH BEND + button
• Pushing these buttons will change main playing
speed temporarily.
• While pushing PITCH BEND + button, the
playing speed increases and speed decreases
while pushing PITCH BEND – button.
• When these buttons are release, the playing
speed returns to the previous speed.
#3
Pitch Slider
• Use this slider to adjust playing speed faster or
slower.
#4
PITCH,
RANGE button
• Push this button to set the PITCH mode on and
off.
• RANGE:
Push this button for more than 1 sec to select
the pitch range. The pitch range can be selected
with the PARAMETERS knob from ±4, 10, 16,
24, 50 or 100%.
#5
KEY ADJUST button
• Push this button to set the KEY ADJUST mode
on and off.
#6
PLATTER SOURCE button
Select the source for Scratch playback and the
manual search/bend mode.
• MAIN:
This button lights up orange.
Manipulate the Main Track sound.
• SAMP.:
This button lights up green only if a sample is
loaded.
Manipulate the Sampler sound via the scratch
disc.
• BEND/SEARCH:
When this button is pushed again, the
BEND/SEARCH mode is selected.
When the Scratch Disc selector is set to
BEND/SEARCH during playback, it works as the
pitch bend function by turning the scratch disc.
When Scratch Disc is turned in the pause or
standby mode, it functions as the manual
search function. In Manual search, you can
move the CUE point around by one frame at a
time (1/75 second) with an audible frame-repeat
sound, da-da-da-da.
)
6
7
)
#7
SCRATCH direction select lever
Select the Scratch play direction.
• BOTH:
When the Scratch Disc is turned, the Scratch
sound is heard in both stroke directions.
• FWD:
When the Scratch Disc is turned, the Scratch
sound is heard in the forward direction only.
#8
BRAKE button
• Push this button to set the BRAKE.
#9
DUMP button
• Push this button to set the DUMP.
$0
REVERSE button
• Push this button to set the REVERSE.
$1
TAP,
LOCK,
AUTO, INPUT BPM
button
• TAP:
When you push this button repeatedly, the Auto
mode turns off and starts measuring your Beats
Per Minute (BPM) by tapping.
• LOCK:
When this button is pressed once while the
auto BPM counter is operating, the data
measured by the auto BPM counter is locked.
• AUTO:
When pushing the TAP button for 1 second,
activates AUTO BPM mode.
The measured BPM is displayed in the character
section of the display.
• INPUT BPM:
When the TAP button is pressed and held in for
more than 2 seconds, the BPM input mode is
set and the BPM value can be input directly with
the EFFECTS knob. When the tap button is
pressed again, the BPM input mode is turned
off and set.
NOTE:
If you select a new track, AUTO BPM mode
turns on automatically.
$2
ECHO/LOOP button
• The ECHO and ECHO LOOP functions can be
selected. The feedback time and feedback ratio
can be selected. Looping for the feedback time
(ECHO LOOP) is possible by setting the
feedback number to "MAX".
4
ENGLISH
$3
FLANGER button
• The feedback time and feedback gain can be
selected.
$4
FILTER button
• One of three filters (LOW PASS, MID PASS and
HIGH PASS) can be selected.
$5
EFFECTS knob
• Use this knob to set parameters of the internal
effector.
$6
PLATTER LED
• This vibrant blue bar provides platter modes at a
glance such as, Scratch Memory, Pitch Bend,
Frame Search and Loaded Disc.
Publicidad
Tabla de contenido
