Remote Control - Revell Control X-RAZOR PRO Manual Del Usuario

1 helICOPTer
1A Stabiliser 1E Counter-rotating
rotor blades
1B Tail rotor
1F Charge socket
1C Landing skid
1G ON-/OFF-switch
1D Side rotors
1H Charge socket
3 InserTIng BaTTerIes (reMOTe COnTrOl)
3A Unscrew the bat- 3B Insert 6 x 1.5 V AA
tery compartment batteries while paying
cover and slide it attention to the direction
downward. in which they must be
inserted – as indicated in
the battery compartment.
4 ChargIng The helICOPTer
Please note: The battery, and motor, must be allowed to cool down for 15 to 30 minutes
after flight before being charged. Failure to do so may result in them becoming damaged.
The charging process must be constantly monitored. Always ensure that the charging
process takes place on a fireproof surface in a fire-resistant environment.
1. Switch off the helicopter and the remote control.
2. Pull the charging cable from the compartment on the front side of the controller (4A).
3. Carefully insert the charging cable plug into the helicopter's charging socket (4B).
The plug must be gently inserted into the charging socket – DO NOT USE FORCE. If the
plug is not correctly inserted into the charging socket, the helicopter may become
damaged and, under certain circumstances, become an injury risk.
4. Set the controller's ON/OFF switch to "ON" (charge).
5. The red power LED lights up and the green charging status LED lights up after
2-3 seconds.
6. When the green charging status LED switches off, it signifies that the charging process
has been completed.
7. Once the charging process has been completed, set the ON/OFF switch to "OFF" and
disconnect the charging cable from the helicopter.
You can also charge your helicopter using the accompanying USB cable:
a. Switch off the helicopter.
b. Carefully insert the charging cable plug into the helicopter's charging socket (4C).
The plug must be gently inserted into the charging socket – DO NOT USE FORCE.
If the plug is not correctly inserted into the charging socket, the helicopter may become
damaged and, under certain circumstances, become an injury risk.
c. Insert the USB plug into an open USB port.
d. The charging process has been completed when the USB plug lights up.
e. After the charging process has been completed, disconnect the USB plug from the
USB port and from the helicopter.
16

2 reMOTe COnTrOl

2A Power-LED 2G Not assigned
2B ON-/OFF-switch 2H Control for forward/
backward flight and
2C Control for thrust
clockwise/antic-
and sideways flight
lockwise rotation
2D Trim adjustment
2I Control for forward/
control for clock-
backward flight and
wise/anticlockwise
clockwise/antic-
rotation
lockwise rotation
2E Lighting ON/OFF
2J Charging status LED
2F Button for motion
2K Charge cable com-
control
partment
3C Push the battery
cover back up and
secure with the
screw.
After a charge time of approx. 50 minutes the helicopter can fly for approx.
5-7 minutes.
Warning notice: The LiPo battery heats up while charging. If it should become hot
and/or changes to the surface begin to appear, immediately discontinue the charging
process!
5 PreParIng FOr Take-OFF
The thrust controller (the left control on the remote control) must point downward
before switching on (5A). We recommend setting the turbo switch to "OFF". Then set
the controller's ON/OFF switch to "ON" (5B). The power LED begins to blink quickly.
Now set the helicopter's ON/OFF switch to the "ON". Place the helicopter on the
ground so that its tail points toward you (5C). Once a connection between the
controller and helicopter has been established, all the LEDS on the helicopter will light
up, and the power LED on the remote control will blink slowly.
Activate the remote control by first moving the thrust controller to maximum and then
back to its starting position. The power LED will now remain permanently lit, signalling
that the helicopter is ready for flight.
6 sTeerIng TrIM aDJusTMenT
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please carefully observe the following instructions: Carefully move the thrust controller
upward to increase the helicopter's altitude to approximately 0.5 to 1 metres.
6A If the helicopter quickly or slowly rotates clockwise by itself...
If the helicopter begins to to quickly or slowly rotate clockwise by itself, rotate the left/
right trim adjustment anti-clockwise until the helicopter no longer rotates by itself.
6B If the helicopter quickly or slowly rotates anti-clockwise by itself...
If the helicopter begins to quickly or slowly rotate anticlockwise by itself, rotate the
left/right trim adjustment clockwise until the helicopter no longer rotates by itself.
17