Preparing To Paint; Painting - Titan SPEEFLO PowrLiner 550 Manual Del Propietário

8. Squirt a teaspoon of Piston
Lube™ (P/N 314-480, sold
separately) into the indicated
area. Light household oil can be
substituted if necessary.
9. Check the engine oil level.
The gasoline engine oil
level is determined by the
manufacturer. Refer to the
engine manufacturer's service
manual (supplied).
10. Fill the gas tank on the engine with unleaded gasoline only.
Do not mix the gasoline with 2-cycle oil.

Preparing to Paint

Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.
NOTE: If this unit is new, it is shipped with test fluid in the
fluid section to prevent corrosion during shipment
and storage. This fluid must be thoroughly cleaned
out of the system before you begin spraying.
Incompatible fluids and paint may cause the valves
to become stuck closed, which would require
disassembly and cleaning of the sprayer's fluid
section.
ImPORTANT: Always keep the trigger lock on the spray gun in
the locked position while preparing the system. If necessary,
loosen the gun holder clamp knob and then engage the spray
gun trigger lock.
1. Place the siphon tube into a container of the appropriate
solvent for the material being sprayed (refer to
recommendations of the material manufacturer). An example
of the appropriate solvent is water for latex paint.
2. Place the return hose into a metal waste container.
3. Turn the PRIME/SPRAY knob to the PRIME
position.
4. Fully depress the pusher stem to make sure
the inlet ball is free.
5. Start the engine:
a. Move the choke lever up to the full
choke position.
b. Push the rubber prime button 7-10
times.
c. Pull the starter rope rapidly and
firmly. Continue to hold the rope as
you let it return. Pull and return the
rope until the engine starts.
d. Once the engine is running, slowly
move the choke lever down to the
closed position.
6. Fluid will begin flowing through
the return hose and into the
waste container. Allow the sprayer to run for 15–30 seconds
to flush the test fluid out through the return hose and into the
waste container.
7. Turn off the sprayer by pressing and holding the engine
shutoff switch until the motor shuts off.
NOTE: make sure that the spray gun does not have a tip or
tip guard installed.
8. Place a metal waste container underneath the spray gun to
catch the solvent.
9. Start the engine.
10. Turn the PRIME/SPRAY knob to the SPRAY
position.
11. Unlock the gun by turning the gun trigger
lock to the unlocked position.
12. Fully pull the spray lever on the cart handle
to rev the engine, pressurize the sprayer, and
English

Painting

Choke
lever
Prime
bulb
Starter
rope
SPRAY
6
trigger the spray gun. Fluid will begin flowing through the
spray hose and out of the gun.
13. Continue to pull the spray lever on the cart handle until the
old solvent/test fluid is gone and fresh solvent is coming out
of the gun.
14. Release the spray lever.
15. Lock the gun by turning the gun trigger lock to the locked
position. If necessary, loosen the gun holder clamp knob and
then engage the spray gun trigger lock. Move the spray gun
to its original position and tighten the clamp knob.
16. Check the entire system for leaks. If leaks occur, turn the
sprayer off and follow the "Pressure Relief Procedure" in this
manual before tightening any fittings or hoses.
17. Follow the "Pressure Relief Procedure" in this manual before
changing from solvent to paint.
Be sure to follow the Pressure Relief Procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for
cleanup.
1. Place a five gallon bucket of material between the bucket
holders on the cart. Make sure the bucket holders hold
the five gallon bucket securely. Adjust the bucket holders
using the thumb screw located underneath each holder, if
necessary.
NOTE: When using this line striper for first time, it may
be helpful to use water in place of paint to gain
familiarity with the operation of the line striper.
After changing from water to paint, test spray
several lines on cardboard, roofing felt, or rosin
paper before striping to ensure correct line width.
2. Place the siphon tube into the bucket of material.
3. Place the return hose into a metal waste container.
4. Turn the PRIME/SPRAY knob to the PRIME
position.
5. Fully depress the pusher stem to make sure
the inlet ball is free.
6. Start the engine:
a. Move the choke lever up to the full choke position.
b. Push the rubber prime button 7-10 times.
c. Pull the starter rope rapidly and firmly. Continue to hold the rope as
you let it return. Pull and return the rope until the engine starts.
d. Once the engine is running, slowly move the choke lever down to
the closed position.
7. Fluid will begin flowing through the return hose and into the
waste container. Allow the sprayer to run for 15–30 seconds
to flush the test fluid out through the return hose and into the
waste container.
8. Turn off the sprayer by pressing and holding the engine
shutoff switch until the motor shuts off.
9. Remove the return hose from the waste container and place it
in its operating position above the bucket of material.
10. Start the engine.
11. Turn the PRIME/SPRAY knob to the SPRAY
position.
12. Unlock the gun by turning the gun trigger
lock to the unlocked position.
13. Fully pull the spray lever on the cart handle
to rev the engine, pressurize the sprayer, and
trigger the spray gun. Fluid will begin flowing through the
spray hose and out of the gun.
14. Continue to pull the spray lever on the cart handle until
material is coming out of the gun.
15. Release the spray lever.
16. Lock the gun by turning the gun trigger lock to the locked
position. If necessary, loosen the gun holder clamp knob and
SPRAY
© Titan Tool Inc. All rights reserved.