Changing A Spray Tip; Stenciling; Operating The Front Caster; Cleanup - Titan SPEEFLO PowrLiner 550 Manual Del Propietário

changing a Spray Tip

Tips can be removed and replaced easily without disassembling the
gun.
Never attempt to change or clean the tip or tip
guard without first performing the "Pressure Relief
Procedure."
1. Perform the "Pressure Relief Procedure" described in the
sprayer's Owner's Manual.
2. Remove the tip from the slot on the tip guard.
3. Insert the new tip into the slot on the tip guard. The arrow on
the tip handle should be pointing in the forward direction for
spraying.
Removing the Seal and Tip seal
1. Remove the tip from the tip
guard.
2. Insert the tip handle through
the front of the tip guard.
3. Push the seal and tip seal out
through the back of the tip
guard.
Identifying Tip Sizes
To identify tip sizes, use the following formula. A "1908" tip size will
be used in this example.
The last two digits divided by two represent the size of the spray
pattern when spraying 6" away from the work surface:
08 ÷ 2 = 4" spray pattern
The first two digits represent the diameter of the orifice on the tip:
19 = .019" orifice
NOTE: Worn spray tips will adversely affect the spray
pattern and result in reduced production, poor
finish, and wasted material. Replace worn tips
immediately.

Stenciling

ImPORTANT: Do not remove the spray gun from the gun holder
and attempt to use it independently. Doing this will will engage
the safety shut-off switch.
The spray gun cannot be removed from the gun holder to perform
stencil work. To stencil with this line striper, make multiple spraying
passes from right to left over the stencil.

Operating the Front caster

The front caster on the cart is designed to track the sprayer in either
a straight line or allow a desired radius to be set. To adjust the front
caster:
1. Loosen the two caster bolts on
the top side of the caster.
2. Move the front wheel to the
proper position for the desired
radius.
3. Re-tighten the bolts to secure
the caster in position.
English

cleanup

• Always flush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting flushed solvents in a one gallon metal container,
place it into an empty five gallon container, then flush
solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
ImPORTANT: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material to
Tip Seal
build up, seriously affecting the performance of the unit.
Tip Seal
Retainer
Tip
Guard
1. Follow the "Pressure Relief Procedure" found in the Operation
Tip
section of this manual.
2. Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
3. Place the siphon tube into a container of the appropriate
solvent (refer to recommendations of the material
manufacturer). An example of the appropriate solvent is
water for latex paint.
4. Place the return hose into a metal waste container.
5. Turn the PRIME/SPRAY knob to the PRIME
position.
6. Start the engine.
7. Fluid will begin flowing through the return
hose and into the waste container. Allow the
fluid to circulate through the sprayer and flush the paint out
of the return hose into the metal waste container.
8. Turn off the sprayer by pressing and holding the engine
shutoff switch until the motor shuts off.
9. Place a metal waste container underneath the spray gun to
catch the paint and solvent.
10. Start the engine.
11. Turn the PRIME/SPRAY knob to the SPRAY
position.
12. Fully pull the spray lever on the cart handle
to rev the engine, pressurize the sprayer,
and trigger the spray gun. Fluid will begin
flowing through the spray hose and out of
the gun.
13. Continue to pull the spray lever on the cart handle until the
material is flushed out of the hose and the solvent coming out
Caster
of the gun is clean.
bolts
14. Release the spray lever.
NOTE: For long-term or cold weather storage, pump Pump
15. Follow the "Pressure Relief Procedure" found in the Operation
section of this manual.
16. Store the sprayer in a clean, dry area.
ImPORTANT: Do not store the sprayer under pressure.
8
Special cleanup instructions for use with flammable
solvents:
Always spray at minimum pressure with the gun spray
tip removed when using mineral spirits or any other
solvent to clean the sprayer, hose, or gun. Static
electricity buildup may result in a fire or explosion in
the presence of flammable vapors.
Saver™ through the entire system.
© Titan Tool Inc. All rights reserved.
SPRAY