Telwin STARTZILLA 2012 Manual De Instrucciones página 6

- turn the ignition key to the start position for no longer than 3
seconds, after start up or a failed attempt a timer will be activated,
shown on the display
possible to try starting the vehicle again.
After a successful start, with the engine running, follow the sequence of
operations below with great care:
- Disconnect the black clamp (negative) from the vehicle;
- Disconnect the red clamp (positive) from the vehicle;
- Remove the starter cable connector from the starter.
It is highly recommended to recharge the starter as soon as possible.
Press button to return to TEST mode
ATTENTION! The icon on the display
constantly shows the temperature of the starter Li battery;
when it decreases below +10°C, icon
these conditions, to achieve the best starter performance, it is
recommended to press button
activate the starter Li battery heating unit.
With the heating unit activated, the icon on the display
switches from blinking to constantly
remains activated until the battery temperature
reaches at least 25°C and, in any case, for a time of no more than 60
min; this aims to prevent the starter Li battery from running down
excessively.
It is always possible to deactivate the heating unit by pressing and
holding button for at least 2 seconds.
The heating unit will deactivate automatically if the Li battery
needs charging.
4.2.1 NOT PROTECTED STARTING MODE
WARNING: Use this mode only in the extreme
case when you have to start a vehicle without
battery or with highly discharged battery; before operation under
these conditions, always read the vehicle instructions manual.
In this mode, the output clamps are not protected neither against
short-circuit nor against polarity reversal.
WARNING: follow the instructions carefully
according the order given below!
Never allow the red and black clamps to come into contact or to
touch a common conductor!
Give special care not to reverse the polarity of the vehicle battery.
The NOT PROTECTED STARTING MODE
12V/24V vehicle batteries. The starter delivers the current necessary to
the starting of the vehicle in case there is no battery or the battery is
highly discharged.
WARNING: follow the instructions carefully
according to the order given below! Never
allow the red and black clamps to come into contact or to touch a
common conductor.
Procedure:
- Make sure that the vehicle to start is o (switch or starting key in the
OFF position);
- Insert the starting cables connector into its plug (Fig. A-10);
- Connect rst the red clamp (POS. (+) to the POSitive terminal (+) of
the battery, keep isolated the black NEGative clamp (-);
- Set the starter in the START mode (read instructions manual);
- Release the button and push it again for at least 5 seconds;
, at the end of which it will be
.
will start to blink. In
for at least 2 seconds to
xed. The heating unit
is available for
- By the button select the battery voltage
model only). After selection, the starting output is ON.
On the display
WARNING: set the nominal voltage of the vehicle
correctly. In the non-protected mode, the starter
does not perform any control.
- Connect the black NEGative clamp (-) to the vehicle chassis or to the
NEGative (-) terminal;
- The message "n.Go" on the display
is waiting to start;
- Turn the vehicle key onto the start position for not more than 10 secs.
WARNING: the on/o
the user. In the non protected mode, the starter
does not give any limit on the start times.
It is a good rule not to exceed with the on/o timings in comparison
with the standard ones, furthermore, as soon as the symbol
appears on the display, the user needs to recharge as soon as
possible.
After starting, perform following steps, carefully, in the order
given below:
- Go back to TEST
- Disconnect the black clamp (negative) from the vehicle;
- Disconnect the red clamp (positive) from the vehicle;
- Pull out the start cables connector from the starter.
It is recommended to recharge the starter as soon as possible.
4.3 POWER SOURCE FUNCTION TO CHARGE EXTERNAL ELECTRONIC
DEVICES
The starter is able to provide power to external electronic devices,
smartphones, tablets, notebooks, etc. from the amount accumulated in
the internal Li battery via a 5V USB port
plug output (Fig. A-6) programmable at 12V, 16V and 19V.
The USB port (Fig. A.7) is always enabled.
The jack plug output
when the starter does not acknowledge any appreciable power
absorption.
4.3.1 Enabling the USB port
The USB port (Fig. A.7) is always enabled except in START
mode.
4.3.2 Enabling the jack plug output
Attention: before connecting any electronic device to the
jack plug output
value programmed and visible on the display is correct. Never
programme the jack plug output with an electronic device
connected, to prevent the risk of damaging the device being
charged is the selected voltage value is the wrong one.
Procedure
- Press and hold for 2 secs button
appear and the selected voltage will blink.
- Press button repeatedly to select the desired voltage, after 5
seconds the numeric value of the selected voltage will stop blinking
and the programmed voltage value will be supplied via the jack plug
output (Fig.A-6).
To change the output voltage value, repeat the operations described
above.
- 6 -
there appears the message "n.Go";
indicates the vehicle
start times are given by
mode, by pressing the button
(Fig. A-7) and a jack
(Fig. A-6) is automatically disabled
(Fig. A-7).
(Fig .A-6)
(Fig. A-6), check that the voltage
, the jack symbol
(12V/24V
;
will