Migatronic AUTOPULS II Guía Rápida página 3

AUTOPULS II - Factory setting
Setting possibilities
Primary parameters:
1 Welding current Area depends on
Wire feed speed
Thickness of material
2 Arc length
Secondary parameters:
1 (DC) Inductance -5.0 - +5.0
1 (Pulse) Pulse frequency
2 Gas pre flow
3 Soft start Off / 1.5 - 18.0
4 Hotstart time
5 Slope down
6 Burnback
7 Gas post flow
8 DUO Plus TM (MIG)
9 Stop amp
r Remote control 0 = internal
1 = torch control
Area Step Factory setting
2T/4T
1 Depending on
program program
0.1
0.1
-9.9 - +9.9 0.1 0.0
0.1 0.0
+/-50 1 0
0.0 - 10.0 0.1 0.2
0.1 1.5
0.0 - 10.0 0.1 0.5
0.0 - 10.0 0.1 0.2
1 - 30 1 5
0.0 - 10.0 0.1 3
0 - 50 1 25
0 - 100 1 50
Programs
No:
Unit
P106
P101
P109
A
P102
m/min
P116
mm
P111
V
P119
P112
-
P201
% P209
P202
s
P311
m/min
P319
s
P312
s
P313
ms
P359
s
P352
%
P353
%
P369
P372
P373
P501
P509
P502
P561
P569
P562
50113774 J
QUICKGUIDE AUTOPULS II
Wire Material Gas
Ø 0.6 mm Fe SG2 ER70S6 CO (100)
2
Ø 0.8 mm Fe SG2 ER70S6 CO (100)
2
Ø 0.9 mm Fe SG2 ER70S6 CO (100)
2
Ø 1.0 mm Fe SG2 ER70S6 CO (100)
2
Ø 0.6 mm Fe SG2 ER70S6 ArCO
Ø 0.8 mm Fe SG2 ER70S6 ArCO
Ø 0.9 mm Fe SG2 ER70S6 ArCO
Ø 1.0 mm Fe SG2 ER70S6 ArCO
Ø 0.8 mm CrNi ER 316 LSI ArCO
Ø 0.9 mm CrNi ER 316 LSI ArCO
Ø 1.0 mm CrNi ER 316 LSI ArCO
Ø 0.8 mm AlMg ER5356/ER5554 Ar (100)
Ø 0.9 mm AlMg ER5356 Ar (100)
Ø 1.0 mm AlMg ER5356/ER5554 Ar (100)
Ø 1.2 mm AlMg ER5356/ER5554 Ar (100)
Ø 0.9 mm AlSi5 ER4043 Ar (100)
Ø 1.0 mm AlSi5 ER4043 Ar (100)
Ø 1.2 mm AlSi5 ER4043 Ar (100)
Ø 0.9 mm AlMg3Mn ER5554 Ar (100)
Ø 1.0 mm AlSi12 ER4047 Ar (100)
Ø 1.2 mm AlSi12 ER4047 Ar (100)
Ø 0.8 mm CuAl8 Brazing Ar (100)
Ø 0.9 mm CuAl8 Brazing Ar (100)
Ø 1.0 mm CuAl8 Brazing Ar (100)
Ø 0.8 mm CuSi3 Brazing Ar (100)
Ø 0.9 mm CuSi3 Brazing Ar (100)
Ø 1.0 mm CuSi3 Brazing Ar (100)
UK
Process
DC+
DC+
DC+
DC+
(82/18) DC+
2
(82/18) DC/P+
2
(82/18) DC/P+
2
(82/18) DC/P+
2
(98/2) DC/P+
2
(98/2) DC+
2
(98/2) DC/P+
2
DC+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+
DC/P+