Preliminary Operations - Cuppone Leonardo Guia De Inicio Rapido

Installazione
Installation
dovrà avere una sezione massima di 10 mm2 (secondo la
norma CEI EN 60335-2-42:2003-09) ed essere di colore giallo
verde;
• essere obbligatoriamente connessa alla
della rete (cavo di colore giallo verde);
• essere obbligatoriamente connessa ad un
termico
secondo quanto riportato nella normativa in vigore
(0.03A Tipo A);
• essere obbligatoriamente connessa ad un
interruzione omnipolare
completa nelle condizioni della categoria di sovratensione III.
Il Fabbricante declina ogni responsabilità per il mancato rispetto
di quanto sopra esposto.
In caso di necessità, il cavo deve essere sostituito dal Ri-
venditore o dal suo servizio assistenza tecnica o comun-
que da una persona con qualifica similare, in modo da
prevenire ogni rischio.
Ed. 0121 - 70702553 REV01 Leonardo Oven - Quick Guide
Installation
Instalación
linea di terra
differenziale
meccanismo di
che consenta una disconnessione
Installation
Установка

Preliminary operations

EN
Fig.1.
Carefully remove the protective film.
If any glue residue is left on the surfaces, remove it with soapy
water but without any corrosive or abrasive products or sharp or
pointed instruments.
Check that all the parts making up the oven are in good
condition and without any faults or breakages, if that is
not the case, contact the Retailer for the procedures to
follow.
Transport and positioning of the oven
on the planned base
Fig.2. Fig.3.
and Fitted with personal protection equipment,
transport the appliance to the installation location. Use suitable
equipment, capable of dealing with its weight: persons not
involved with the appliance installation may not pass through or
stand in the work area during the appliance assembly. During the
transport, pay particular attention to passing through openings
and/or doors. To lift the appliance, it is vital to fit the 4
supplied (located inside the oven chamber) and use a
attach to them. The frame is not supplied by the Manufacturer
and must therefore be obtained by the installer; it must be
constructed with material, measurements and thickness suitable
for lifting the equipment safely without causing damage to
persons or to the equipment itself.
It is absolutely forbidden to lift or move the
equipment using a single coupling point as this
would cause serious structural damage to it.
Fig.4.
Position the appliance on the base provided.
It must:
• be flame and heat resistant;
• be perfectly flat;
• be stable;
• bear the weight of the appliance and any accessories (see the
following table).
Model refractory
surface
LN2T/1TS - h. 18 207 kg - 207 lb
LN2T/1TSH - h. 25 222 kg - 489 lb
LN3T/1TS - h. 18 247 kg - 544 lb
LN3T/1TSH - h. 25 262 kg - 577 lb
LN650/1TS 387 kg - 853 lb
For a correct installation it is necessary to seal the gap
created between the base of the oven and the support
surface, using silicone, authorized for applications in the
food sector, to be placed along the contour of the base of the
oven and such as to prevent the accumulation of dirt where it is
not possible to carry out regular cleaning given the small size of
the access to the areas involved in the deposit of dirt.
Please check that the installation rooms are suitable and that the
minimum distances from the
combustible materials
and
Fig.5.
Remove the eyebolts and refit the previously removed
screws.
25
eyebolts
frame
rusticated
surface
193 kg - 425 lb
208 kg - 458 lb
226 kg - 498 lb
241 kg - 531 lb
347 kg - 765 lb
walls, other equipment, objects
Fig.6.
are complied with (see
to
).