Preliminary Operations; Electrical Connection - Cuppone Caravaggio Guia De Inicio Rapido

Installazione
Installation
Transport
EN
Fig.1.
Fitted with personal protection equipment, trans-
port the appliance to the installation location. Use a suitable vehi-
cle capable of withstanding the weight of the same.
Model single
CR 5 230 kg - 507 lb
CR 8 270 kg - 595 lb
Persons not involved with the appliance installation may not
pass through or stand in the work area during the transport of
the appliance. During the transport, pay particular attention to
passing through openings and/or doors.

Preliminary operations

Fig.2.
Carefully remove the protective film.
If any glue residue is left on the surfaces, remove it with soapy
water but without any corrosive or abrasive products or sharp or
pointed instruments.
Check that all the parts making up the oven are in good con-
dition and without any faults or breakages, if that is not the
case, contact the Retailer for the procedures to follow.
Positioning
The positioning room must comply with the instructions provid-
Fig.3.
ed in
Fig.4.
The oven must be placed on a base, built by the Manu-
facturer or by yourself that:
• is flame and heat resistant;
• is perfectly stable and level;
• withstands the weight of the appliance.
In both cases, silicone the gap between the oven and the sup-
port or the bearing surface, using high temperature resistant sili-
cone (for USA versions only).
Comply with the measurements shown in the figure
Serial number plate reading
Fig.6.
The serial number is on the right hand side of the ap-
pliance. It provides important technical information that is vital
in case of a request for maintenance or repair of the appliance:
please do not remove, damage or modify it.
Smoke extraction
The oven is fitted with a flue in the top to get rid of the steam
from the cooking chamber.
This steam, together with the one from the door during the work
must be conveyed outside
phases,
ways:
Fig.7.
hood supplied by the Manufacturer
through a
A
perfect compatibility with the oven. For correct assembly and
fixing to the oven, see the sheet attached to it; the evacuation
flue must be for the exclusive use of the appliance, comply
with current regulations and have a diameter that allows the
ø150 mm [Ø 5.91 in.]
passage of a
corresponds to the diameter of the tube to be fitted on the
hood (not supplied).
hood
through a belonging to the user, of suitable capacity,
B
300 mm [Ø 11.81 in.]
placed at about
Installation
Instalación
double
450 kg - 992 lb

Electrical connection

520 kg -1146 lb
side of the oven.
plug: they must both be fitted by qualified personnel. The cable
must be only
be suitable for the consumption and connection of the oven to
the electrical mains.
To connect the cable to the appliance, remove the RH side panel
of the oven, let the cable through the cable gland provided and
connect it to the terminal block correctly.
For a correct electrical connection, the appliance must:
• be included in an
Fig.5.
• must be
• must be connected to a
• must be connected to an
The Manufacturer accepts no liability for failure to comply with
the above.
in one of the following
that ensures
evacuation pipe which
from the oven;
24
Installation
Установка
through an adequate
C
the user connected to the oven flue: in this case a draught
switch must be installed between the extractor and the oven
chimney (the extractor, switch and tube are not supplied
by the Manufacturer). In this type of installation, the fumes
resulting from the opening of the door will not be extracted.
The electrical connection must be carried out
by qualified personnel after reading the safety warnings
at the beginning of the manual.
Before installing the appliance,
comply with the regulations in force
where it is going to be used and
indicated on the appliance rating plate
Fig.9.
The appliance is supplied without either power cable or
of the type stated
If the oven is fitted with a double chamber, there are two
power cables and two plugs.
equipotential system
with the legislation in force. This connection must be made
between the various devices with the terminal marked with the
equipotential symbol . The cable must have a maximum
cross-section of 10 mm2 (in compliance with IEC EN 60335-2-
42:2003-09) and must be yellow-green;
grounded
to the mains (green-yellow wire);
thermal differential switch
pliance with the regulations in force (0.03A A type);
omnipolar circuit breaker
complete disconnection in overvoltage III category conditions.
If required, the cable can be replaced by the Dealer or its
technical service or by a person with similar qualifications
to prevent any risk.
extraction system
supplied by
exclusively
check that systems
in the country
with the specifications
on the RH
and the plug fitted to it must
in compliance
in com-
allowing