Preliminary Operations; Electrical Connection - Cuppone Giotto GT 110 Guia De Inicio Rapido

Installazione
Installation

Preliminary operations

EN
Fig.1.
Carefully remove the protective film.
If any glue residue is left on the surfaces, remove it with soapy water
but without any corrosive or abrasive products or sharp or pointed
instruments.
Check that all the parts making up the oven are in good
condition and without any faults or breakages, if that is not the
case, contact the Retailer for the procedures to follow.
Fig.2.
Install collar "A" on the oven gas flue using the three screws provided.
Oven transport and positioning
Move the oven to the desired location, see from
Comply with the oven minimum distances from the
appliances, objects combustible materials listed in
and
Serial number plate reading
Fig.12.
The serial number is on the right hand side of the appliance.
It provides important technical information that is vital in case of a
request for maintenance or repair of the appliance: please do not
remove, damage or modify it.
Smoke extraction
Fig.13.
The oven is fitted with an adjustable exhaust in the top to get rid of the
steam from the cooking chamber.
This steam, together with the one from the door during the work
must be conveyed outside
phases,
hood supplied by the Manufacturer
• through a
A
perfect compatibility with the oven. For correct assembly and
fixing to the oven, consult the sheet attached to it; the evacuation
flue must be used only by the appliance, have a
minimum diameter and comply with the regulations in force.
hood
• through a belonging to the user, of suitable capacity,
B
placed at about 300 mm [Ø 11.81 in.] from the oven;
extraction system
• through an adequate
C
in this case a draught switch must be installed between the
extractor and the oven chimney (the extractor and switch are
not supplied by the Manufacturer). In this type of installation, the fumes
resulting from the opening of the door will not be extracted.

Electrical connection

The electrical connection must be carried out
qualified personnel after reading the safety warnings at the
beginning of the manual.
Before installing the appliance,
with the regulations in force
with the specifications indicated on the
to be used and
appliance rating plate
on the RH side of the oven.
Fig.14.
The appliances have a "D" socket on the back, where the "C" socket
supplied must be connected.
Fig.15.
On the latter, a plug "B" and a power cable "A" of adequate capacity and
section must be fitted by a qualified electrician (see table on the next
page) (both not supplied).
The following pages show the electrical diagrams: please refer to
the one of the specific model to connect.
For a correct electrical connection, the appliance must:
equipotential system
• be included in an
legislation in force. This connection must be made between the
various devices with the terminal marked with the equipotential
Ed. 1020 - 70702563 REV00 Giotto Oven - Quick Guide
Installation
Instalación
Fig.3. Fig.11.
to
walls,
other
Fig.2.
in one of the following ways:
that ensures
150 mm [Ø5.91 in.]
supplied by the user:
exclusively
by
check that systems comply
in the country where it is going
in compliance with the
Installation
Установка
symbol . The cable must have a maximum cross-section of
10 mm2 (in compliance with IEC EN 60335-2-42:2003-09) and must
be yellow-green;
grounded
• must be to the mains (green-yellow wire);
thermal differential switch
• must be connected to a
with the regulations in force (0.03A A type);
• must be connected to an
complete disconnection in overvoltage III category conditions.
The Manufacturer accepts no liability for failure to comply with the
above.
If required, the cable can be replaced by the Dealer or its
technical service or by a person with similar qualifications to
prevent any risk.
Pre-testing and final inspection
The oven is checked and tested in the Manufacturer's plant before being
delivered to the customer.
The "production process check sheet" enclosed with it guarantees that
each
step in the production process, from assembly to packaging, was
carefully checked from both the operating and safety standpoints.
Finish off explaining to the user how to use the appliance in an optimal
and safe way and how to carry out ordinary maintenance and cleaning.
Checking the operation and first start-up
Start the appliance following the instructions in the "Use and
Maintenance" manual annexed: monitor it during the whole test and
check that all the electrical components work properly.
The first time
you use the oven, we recommend you set the
150°C - 302°F,
temperature at
8 hours, without placing any food
percentage for at least
During this time, keep the chimney flue fully open and the hood, if
present, ON.
In this first phase, because of the humidity evaporating from the
insulating materials, the oven will give out unpleasant smells and fumes
that will gradually disappear during the following operating cycles.
25
in compliance
omnipolar circuit breaker
allowing
80% 20%
top percentage,
inside.
bottom