Smith & Nephew SPIDER Modo De Empleo página 3

3. Insert the male post of the sterile Piggy Back into the non-sterile female
receptor on the SPIDER/SPIDER2 Quick Connect. Ensure the Quick Connect
Lock is not locked until after insertion as this prevents the Piggy Back from
engaging properly. Pull up on Piggy Back to ensure connection is secure.
4. Drape the Piggy Back and SPIDER/SPIDER2 with the SPIDER Drape. If using
the SPIDER2, the Switch Drape REF 72203300 may be used.
5. If the Switch Drape is used, plug the proximal connector into the Switch
Drape Connection Receptacle.
6. The 3D Connector is connected to the Piggy Back (an audible click ensures
it is secured). Ensure all of the connections are secure, and then lock the
Quick Connect Locks.
7. The Leg Accessory is connected to the 3D Connector by inserting the 3D
Connector Ball into the Leg Accessory Ball Clamp (Figure 4). The Clamp
must be fully open by rotating the Handle counterclockwise as far as
possible. To close the clamp, rotate clockwise.
Figure 4. Connect Leg Accessory to 3D Connector
8. If the Switch Drape is used, apply the Distal Activation Button to the top of
the 3D Connector (Figure 5).
Figure 5. Adhere Distal Activation Button to the top of 3D Connector
9. Loosen the Handle on the Leg Accessory by ½ of a turn, and then orient
the Leg Accessory over the patient's operative leg with the heel of the Leg
Accessory lining up over the heel of the patient.
10. Place the foot of the operative leg onto the SPIDER Leg Accessory. Ensure
that the patient's heel sits deep into the heel of the Leg Accessory.
11. Wrap the self adhering bandage around the foot, shin and SPIDER Leg
Accessory. Do not over tighten (Figure 6).
Figure 6. Wrap Leg and Accessory with Self adhering Wrap
Instructions for Use
SPIDER Leg Accessory
Intraoperative Position Changes
1. The patient's leg can be repositioned intraoperatively by sterile surgical staff
quickly and easily.
2. Leg position can be altered by grasping the operative foot and the 3D
connector, stepping on the SPIDER/SPIDER2 Foot Pedal, or pressing the
Switch Drape Button, moving the leg to the desired position and stepping
off the Foot Pedal or releasing the Button.
3. Rotation and repositioning of the foot is accomplished by loosening the Ball
Clamp by turning the Handle half a turn in a counterclockwise direction,
repositioning the foot and retightening the Handle (Figure 2).
4. To release the leg from the SPIDER/SPIDER2, turn the Handle
counterclockwise as much as possible and pull the Clamp off of the Ball
of the 3D Connector. The leg can then be manipulated and moved. To
re-attach to the SPIDER/SPIDER2, place the Clamp back over the Ball of the
3D Connector and retighten the Handle by turning clockwise.
Cleaning/Sterilization
• Discard disposable components and wipe the entire SPIDER/SPIDER2
assembly with mild detergent/disinfectant following each case.
• Do not allow cleaning liquids to get into SPIDER/SPIDER2 joints.
• Do not autoclave the SPIDER/SPIDER2.
• Clean and sterilize according to 79-99-04 Cleaning and Sterilization
Instructions.
Autoclave Type
Minimum Exposure Time
Minimum Temperature: 132° C (270° F)
Note: Allow at least 20 minutes to cool at room temperature.
Warranty
This product has a standard 12-month parts and labor warranty against
manufacturing defects.
For Further Information
If further information on this product is needed, contact Smith & Nephew
Customer Service at +1 800 343 5717 in the U.S., or an authorized
representative.
©2014, 2018 Smith & Nephew, Inc. All rights reserved.
English
Gravity Pre-Vac
15 minutes 3 minutes
127-99-01 Rev. E
3