Serial Interface (Rs 232); Usb Port; Headphones; Mains Power Connection - TechniSat HD-Vision 32 Instrucciones De Funcionamiento

4.8 Serial interface (RS 232)

The RS 232 interface is used for updating the operating software
and for pre-programming the TV using a PC.

4.9 USB port

The USB port is used for updating the operating software and for
pre-programming the TV using a PC or USB device. Furthermore,
you can connect a USB device to this port.

4.10 Headphones

If you want to use headphones, connect them to the headphone
socket at the back of the TV set on the left.

4.11 Mains power connection

You must only connect the LCD TV set to the mains power supply
(230 V / 50 Hz) after you have fi rst connected the television to all the
other components. This will ensure the TV set or other components
do not suffer irreparable damage.
4.12 PC
If your PC has a DVI output, we recommend you connect the PC
using a DVI-HDMI cable to the HDMI connection of the television
set. Otherwise, please use a VGA cable and connect the PC to the
VGA socket of the television set.
> Afterwards, use the 0/AV button on the remote control to switch
the television set to VGA playback or HDMI playback.
If you have established the connection using a DVI-HDMI cable,
the switchover should take place automatically.
Before connecting the PC to the television set, it makes good
sense to confi gure the resolution of the graphics card so it supplies
a picture in one of the formats supported by the television. The
supported formats are listed in the specifi cations (Point 14). One
of the resolutions supported, for example, is 1024*768@60Hz.
Please refer to the user manual of your PC's operating system for
information on how to set a particular resolution for your graphics
card. In Windows you can generally fi nd this setting using Start
Menu -> Control Panel -> Appearance and Themes -> Display ->
Settings.
You will obtain optimum results (a full-screen picture with the best
possible resolution) if you supply the panel with a signal in its native
resolution (1366*768). In accordance with the VESA CVT standard,
a resolution of 1360*768@50Hz is available that is therefore
an almost perfect match. The exact parameters are listed in the
specifi cations (Point 14). Your television informs the PC about this
resolution via DDC. Unfortunately, there is no assurance that the
graphics card driver will always accept it.
If you see slight interference or have a blurred picture with a
connection via the VGA input, please correct this using the Trigger
level setting in Menu -> Settings -> VGA setting -> Trigger level.
If you need to adjust the horizontal position of the picture you can do
so using the Horizontal position control in the same menu.
All manuals and user guides at all-guides.com
EN

5 First-time installation

Once you have read the safety notices and connected the TV set as
described in Chapter 4, you can switch on the TV set as described
in Chapter 6. When you switch on the TV set for the fi rst time the
AutoInstall installation assistant starts automatically.
The installation assistant will help you easily confi gure the most
important settings on the television set.
You can cancel the fi rst-time installation procedure at any time by
pressing the red function button. You can return to the previous
installation step by pressing the green function button. This therefore
allows you at any time to correct something you might have entered
incorrectly.
The fi rst-time installation procedure described here only serves as
an example. The actual setup procedure depends on the changes
that you make to the settings. Therefore, please follow the on-screen
instructions very carefully.
Menu language
The installation assistant starts by asking you to select a
Language.
> Use the up/down arrow buttons to mark the desired menu
language.
> Confi rm with OK.
Audio language
> Use the up/down arrow buttons to select the preferred audio
language.
> Confi rm with OK to accept the selected setting.
Time zone setting
> Use the up/down arrow buttons to select the time zone for
your country.
The clock time will be adjusted automatically according to the
setting you select.
> Confi rm with OK.
Broadcast area
> Use the up/down arrow buttons to select the broadcast area in
which you are located.
After the installation assistant has completed, the system will
sort the TV channels and radio stations in the list of favourites
according to the selection you made here.
> Confi rm with OK to accept the selected setting.
Displaying 4:3 programmes
Programmes broadcast with an aspect ratio of 4:3 can be displayed
in their original format or always in 16:9 format or with optimal
utilisation of the screen.
> Use the up/down arrow buttons to select how programmes
broadcast in 4:3 format should be displayed.
> Confi rm with OK to accept your selection and then proceed to
the menu for choosing the available reception signals.
7