Assembly Instructions; How To Assemble Your Child Seat On A Lugagge Carrier; How To Adjust The Child Seat To Your Child; How To Remove Your Child Seat From A Lugagge Carrier - Bobike ONE MAXI E-BD Manual

1. Turn the child seat down in order to access the base (H).
2. To remove the base of the child seat you have to open the jaws (I),
pressing one of the jaws, pressing down the button and pulling out. With
the other hand you have to pull out the base, and finally press and pull the
other jaw to completely remove the base.
3. You shall free the metallic clamps (H2). You can use the Allen key nrº5
(H6) provided. Unscrew (relieve only) in diagonal two opposite screws (H1)
in the base , as shown in the picture. Then do the same for the 2 screws
(H3). The application of protective caps (H4) is mandatory on the
metallic clamps (H2) so that the carrier is not damaged.
4. After releasing the screws (H1 + H3) centrally place the base (H) on the
carrier. When you tighten the base it could move to the right or left. Note
that you should always place it at the centre of the carrier. Now, you
must tighten the 2 screws (H3), and then the 4 Screws (H1) in cross. You
must tighten it with the necessary strength so the base would be well fixed
to the carrier and do not move at all with a recomended torque of 6 N.m.
5. Next step is to fasten the baby-seat to the base. This is an important step
to ensure the safety of the child and the cyclist, so you should make sure
to comply strictly with the following instructions. Place the child seat as
seen in the picture, so that you can insert the safety metal plate of the child
seat (J), and secure it in the insertion opening for the metallic protection
system (H5), marked by the red arrow. After assuring that it is properly
fixed, push down the child seat, in order to secure it to the base. The child
1. To put the child into the seat you must first loosen the belt (B). First,
extend the belts to the maximum by pressing the adjuster button (B2.1)
of the belt guide (B2), then pull it up. This will simplify the placement of
the seat belt when the child is in the seat. We recommend that the child's
helmet be put on after the belt is adjusted.
2. To place the child in the seat, first undo the belt. Start by pressing
the releases on the sides of the safety buckle (K1) and pull the buckle
(K) upwards, so that it slides out of the socket (K2). Place the child in
the seat. Insert the safety buckle (K) in its socket again (K2). Make sure
that the buckle socket (K2) is correctly positioned and does not hurt
the child.
3. Next adjust the belt to the size of the child to ensure that the child is
firmly secured. First adjust the height of the belt. To do this, pull the straps
(B3) according to the size of the child. Before starting the journey, always
check that the child is secured and that the belt is snug but not so tight that
it hurts the child. To lengthen the belt, press the release on the adjuster
buckle (B2).
1. Detach the safety-belt (C) in order to remove the child bicycle seat.
2. Press the jaws (I) and pull both of them out. At the same time, pull the child seat up and back.

ASSEMBLY INSTRUCTIONS

ONE MAXI E-BD

HOW TO ASSEMBLE YOUR CHILD SEAT ON A LUGAGGE CARRIER

ASSEMBLY INSTRUCTIONS
ONE MAXI E-BD

HOW TO ADJUST THE CHILD SEAT TO YOUR CHILD

ASSEMBLY INSTRUCTIONS
ONE MAXI E-BD

HOW TO REMOVE YOUR CHILD SEAT FROM A LUGAGGE CARRIER

seat will be properly locked to the base after you hear a click on
both sides, on both the opening and clamping jaws (I), also marked
with two red arrows.
6. The child seat has a centre of gravity (F) (inscribed on the child seat) that
must be positioned in front of the rear wheel axle. If it is positioned behind
the axle, the distance must not exceed 10 cm. If the centre of gravity is
more than this distance from the axle, adjust the seat to the correct
position. Special care must also be taken when positioning the child seat
to ensure that the cyclist does not touch the child seat with his feet when
cycling. Make sure that the mounting base (H) is firmly attached to
the carrier before proceeding. This step is extremely important
for child and cyclist safety. Note: In Germany, according to the German
Traffic Law StVZO, bicycle seats may only be fixed so that 2/3 of the seat
depth or the Gravity Center of the seat is located between the front and
rear axle of the bicycle.
7. Pass the safety belt (C) around the bicycle frame. Adjust it as shown
in the picture, under tension. Make sure that remain loosen belt is not in
contact with the wheel. This step is extremely important for the child's
safety.
8. Make sure you have followed and fulfilled all the instructions given.
When done so, the child bicycle seat is ready for use. IT IS MANDATORY
TO READ the following chapter on safety instructions about using
your child bicycle seat.
4. To complete this step and ensure that the child is safe, adjust the lower
lap belt adjuster (B4) according to the size of the child, sliding it up or
down.
5. After the final adjustment of the belt, check that the shoulder straps (B1)
are not too close to the child's neck to avoided hurting them. The straps
should be positioned slightly above the shoulders, as shown in the picture.
6. To remove the footrest strap, lift it slightly to release it from the footrest
peg (D3) and slide it upwards to disengage it from the footrest slot (D).
Then pass the thin end of the plastic strap (D1) through the hole in the
footrest, as shown in the picture.
7. Once the strap is correctly positioned, it can be easily slid up or down
according to the child's foot. Next slot one of the openings in the strap (D1)
over the foot support peg (D3). If you want to remove the strap (D1), twist
it slightly to loosen it from the foot support peg (D3).
8. Adjust the height of the footrest according to the size of the child. To
do this, raise the lever (D2) and slide it up or down for the required height.
After deciding on the correct height, lower the lever (D2) to lock in place.
5